Skip to content
Tinkercaster

Seymour Duncan wiring

Three Strat Stack Plus pickups, five-way, push/pull split volume, two tones

3 Strat Stack Plus · 5-way · push/pull vol (3 coil split) · 2T

Transcribed from the manufacturer wiring sheet.

Viewed from the back of the controls, as you solder them.

Three Strat Stack Plus pickups, five-way, push/pull split volume, two tonesThree Strat Stack Plus pickups, five-way, push/pull split volume, two tones: 3 Strat Stack Plus · 5-way · push/pull vol (3 coil split) · 2T. Original Tinkercaster drawing with labelled terminals.Neck stackMiddle stackBridge stack250k250k250k22nFwhiteredblackbarewhiteredblackbarewhiteredblackbareT1T2T3T4T5T6T7T8lug1lug2lug3sw1sw2sw3sw4sw5sw6lug1lug2lug3lug1lug2lug3abtipsleevegroundNeck stackMiddle stackBridge stack5-Way Blade SwitchVolume push/pull · 250kTone 1 (neck) · 250kTone 2 (middle) · 250k.022 cap · 22nFOutput jackBridge ground

Open the interactive diagram to zoom, move components and try the switches.

Parts and values

In the drawingValuePart
Neck stack—Strat Stack PlusAs specifiedSame wiring for Strat Stack Plus
Middle stack—Strat Stack PlusAs specifiedSame wiring for Strat Stack Plus
Bridge stack—Strat Stack PlusAs specifiedSame wiring for Strat Stack Plus
5-Way Blade Switch—Oak Grigsby 5-WayExample part
Volume push/pull250kNot on the sheet; stand-in250k Push-Pull DPDTExample part
Tone 1 (neck)Source: Tone 1250kCTS 250k Audio PotExample part
Tone 2 (middle)Source: Tone 2250kCTS 250k Audio PotExample part
.022 cap22nFOrange Drop .022µFExample part
Output jack—Switchcraft #11Example part
Bridge ground—Bridge ground wireGeneric

Every pickup is the maker's own. “As specified” means the sheet names that part. “Example part” means the sheet names no model: the pickup shown is one of the maker's with the same leads, and any pot, cap or switch with the same value and lugs will do. “Generic” is a plain part such as a ground wire. “Not on the sheet; stand-in” means the sheet prints no value for that part, so the value shown is the usual one, not the maker's.

Understand this wiring

All Seymour Duncan wiring guides →

Connections

In soldering order: grounds first, then the switch, the pickups and the signal path.

#FromToHow
1Push/pull left lug nearest the potVolume casing (upper Solder spot)To a pot casingblack
2Neck stack gndVolume 250k push/pull casingWireblack
3Neck stack bareVolume 250k push/pull casingWirebare
4Middle stack gndVolume 250k push/pull casingWireblack
5Middle stack bareVolume 250k push/pull casingWirebare
6Bridge stack gndVolume 250k push/pull casingWireblack
7Bridge stack bareVolume 250k push/pull casingWirebare
8Bridge ground wireVolume 250k push/pull casingGround wire to bridge.Wireblack
9Volume 250k push/pull lug1Volume 250k push/pull casingWireground
10.022 cap bTone 1 casingWireblack
11Tone 1 casingVolume 250k push/pull casingWireblack
12Volume 250k push/pull casingOutput jack sleeveWireblack
13Tone 2 casingVolume 250k push/pull casingWireblack
14Bridge stack hot5-Way Blade Switch T3Wireblack
15Middle stack hot5-Way Blade Switch T1Wireblack
16Neck stack hot5-Way Blade Switch T2Wireblack
175-Way Blade Switch T4Volume 250k push/pull lug3Wireblack
185-Way Blade Switch T8Push/pull left middle lugWireblack
19Bridge stack red tap5-Way Blade Switch T7Bridge red; the sheet's red leads from the stacks run to the blade's lower row and the push/pull.Wirered
20Neck stack red tap5-Way Blade Switch T6Neck red; it hops over the bridge red on the sheet.Wirered
215-Way Blade Switch neck lug (T2)Tone 1 middle lugThe neck tone is fed from the neck pickup's lug on the blade, as the sheet draws it.Wireblack
225-Way Blade Switch middle lug (T1)Tone 2 lug1The middle tone is fed from the middle pickup's lug on the blade, as the sheet draws it.Wireblack
23Middle stack red tapPush/pull right middle lugMiddle red; bends down to the push/pull.Wirered
24Push/pull left lug nearest the potPush/pull right lug nearest the potShort jumper.Wireblack
25Volume 250k push/pull lug2Output jack tipWireblack
26Tone 1 lug1.022 cap aWireblack
27Tone 1 lug1Tone 2 lug2On the sheet a jumper runs from the upper tone's third lug, which also carries the .022 cap, to the lower tone's middle lug.Wireblack

What each position does

SettingThe sourceEngine result
Position 1 · push: bridgeLegend: when push/pull is DOWN all pickups are hum-cancelling.Bridge stack (both coils).
Position 1 · pull: bridge splitLegend: when push/pull is UP all pickups are true single coils.Bridge stack (split to one coil).
Position 2 · push: bridge + middleLegend: when push/pull is DOWN all pickups are hum-cancelling.Middle stack (both coils) and Bridge stack (both coils) in parallel.
Position 2 · pull: bridge split + middle splitLegend: when push/pull is UP all pickups are true single coils.Middle stack (split to one coil) and Bridge stack (split to one coil) in parallel.
Position 3 · push: middleLegend: when push/pull is DOWN all pickups are hum-cancelling.Middle stack (both coils).
Position 3 · pull: middle splitLegend: when push/pull is UP all pickups are true single coils.Middle stack (split to one coil).
Position 4 · push: middle + neckLegend: when push/pull is DOWN all pickups are hum-cancelling.Neck stack (both coils) and Middle stack (both coils) in parallel.
Position 4 · pull: middle split + neck splitLegend: when push/pull is UP all pickups are true single coils.Neck stack (split to one coil) and Middle stack (split to one coil) in parallel.
Position 5 · push: neckLegend: when push/pull is DOWN all pickups are hum-cancelling.Neck stack (both coils).
Position 5 · pull: neck splitLegend: when push/pull is UP all pickups are true single coils.Neck stack (split to one coil).

Checked with the Tinkercaster wiring engine against the switching the source describes.

  • The sheet prints no pot values; 250k stand-ins are used for the push/pull and tones.
  • The push/pull is one DPDT whose poles ground the middle red directly and the blade's second-pole common, as on the single-tone push/pull sibling.
  • Passive tone analysis is topology-only (toneReachesSignal).

Before you solder

Ticks are kept in this browser only, as a reminder. They are not a check of your joints. New to soldering? Read the soldering cheat sheet .

Check before plugging in

    Measure across the output jack with a multimeter on its resistance range. No exact readings are given where the source does not specify the pickups.