Skip to content
Tinkercaster

Seymour Duncan wiring

Two Strat Stack Plus pickups and a single-coil-sized humbucker, 5-way blade, push/pull split volume and tone

Two Strat Stack Plus · Single-coil-sized humbucker (bridge) · 5-way blade · Push/pull volume (3 coil split) · One tone

Seymour Duncan sheet: Strat Stack Plus pickups in the neck and middle and a single-coil-sized humbucker in the bridge, on a 5-way blade with a push/pull volume titled '3 coil split', one tone and a .047 cap. The sheet prints no pot values. Pull the knob and each selected pickup drops to one coil: the middle red is grounded directly, the bridge and neck links through the blade's second pole.

Viewed from the back of the controls, as you solder them.

Two Strat Stack Plus pickups and a single-coil-sized humbucker, 5-way blade, push/pull split volume and toneTwo Strat Stack Plus pickups and a single-coil-sized humbucker, 5-way blade, push/pull split volume and tone: Two Strat Stack Plus · Single-coil-sized humbucker (bridge) · 5-way blade · Push/pull volume (3 coil split) · One tone. Original Tinkercaster drawing with labelled terminals.Neck Strat Stack PlusMiddle Strat Stack PlusBridge single-coil-sized humbucker250k250k47nFwhiteredblackbarewhiteredblackbareblackgreenwhiteredbareT1T2T3T4T5T6T7T8lug1lug2lug3sw1sw2sw3sw4sw5sw6lug1lug2lug3abtipsleevegroundNeck Strat Stack PlusMiddle Strat Stack PlusBridge single-coil-sized humbucker5-way bladeVolume (push/pull) · 250kTone · 250k.047 cap · 47nFOutput jackGround wire to bridge

Open the interactive diagram to zoom, move components and try the switches.

Parts and values

In the drawingValuePart
Neck Strat Stack Plus—Strat Stack PlusExample part
Middle Strat Stack Plus—Strat Stack PlusExample part
Bridge single-coil-sized humbuckerSource: Bridge single coil sized humbucker—Little '59 SL59-1 Bridge (Strat-size)Example partSame wiring for JB Jr. SJBJ-1 Bridge (Strat-size), Hot Rails SHR-1 Bridge (Strat-size)
5-way blade—Oak Grigsby 5-WayExample part
Volume (push/pull)Source: Volume push/pull (3 coil split)250kNot on the sheet; stand-in250k Push-Pull DPDTExample part
Tone250kNot on the sheet; stand-inCTS 250k Audio PotExample part
.047 cap47nFOrange Drop .047µFExample part
Output jackSource: Output Jack—Switchcraft #11Example part
Ground wire to bridge—Bridge ground wireGeneric

Every pickup is the maker's own. “As specified” means the sheet names that part. “Example part” means the sheet names no model: the pickup shown is one of the maker's with the same leads, and any pot, cap or switch with the same value and lugs will do. “Generic” is a plain part such as a ground wire. “Not on the sheet; stand-in” means the sheet prints no value for that part, so the value shown is the usual one, not the maker's.

Understand this wiring

All Seymour Duncan wiring guides →

Connections

In soldering order: grounds first, then the switch, the pickups and the signal path.

#FromToHow
1Push/pull left lug nearest the potVolume casing (upper Solder spot)To a pot casingblack
2Neck blackVolume casing (upper Solder spot)To a pot casingblack
3Neck drainVolume casing (upper Solder spot)Drawn gold.Shield or groundbare
4Middle blackVolume casing (upper Solder spot)To a pot casingblack
5Middle drainVolume casing (upper Solder spot)Drawn gold.Shield or groundbare
6Bridge greenVolume casing (upper Solder spot)To a pot casinggreen
7Bridge bareVolume casing (upper Solder spot)Drawn light grey beside the green.Shield or groundbare
8Ground wire to bridgeVolume casing (upper Solder spot)To a pot casingblack
9Volume third lugVolume casingLug bent onto the casing under the lower Solder spot.To a pot casing
10.047 capTone casing (Solder spot)To a pot casing
11Tone casing (Solder spot)Volume casing (lower Solder spot)To a pot casingblack
12Volume casing (lower Solder spot)Jack sleeveWireblack
13Bridge blackBlade upper-left row, first lugLabelled 'bridge black'; arcs over the top of the blade.Wireblack
14Middle whiteBlade upper-left row, second lugLabelled 'middle white'; the inner of the two white loops.Wirewhite
15Neck whiteBlade upper-left row, third lugLabelled 'neck white'; the outer white loop.Wirewhite
16Blade upper-left row, fourth lugVolume first lugLoops under the blade.Wireblack
17Bridge redBlade lower-right row, second lugRuns beside the bridge white to the same lug.Wirered
18Bridge whiteBlade lower-right row, second lugRuns beside the bridge red to the same lug.Wirewhite
19Neck redBlade lower-right row, fourth lugPasses behind the end of the bridge cable on its way to the blade.Wirered
20Blade lower-right row, first lugPush/pull left middle lugThe black wire carries the hops where it crosses the pickup leads.Wireblack
21Middle redPush/pull right middle lugWirered
22Push/pull left lug nearest the potPush/pull right lug nearest the potShort jumper.Wireblack
23Volume middle lugJack tipThis wire carries the hops over the two ground wires below the volume.Wireblack
24Volume first lugTone outer lugWireblack
25Tone middle lug.047 capWireblack

What each position does

SettingThe sourceEngine result
Position 1 · push: bridgeLegend: when push/pull is DOWN all pickups are hum-cancelling.Bridge single-coil-sized humbucker (both coils).
Position 1 · pull: bridge splitLegend: when push/pull is UP all pickups are true single coils.Bridge single-coil-sized humbucker (split to one coil).
Position 2 · push: bridge + middleLegend: when push/pull is DOWN all pickups are hum-cancelling.Middle Strat Stack Plus (both coils) and Bridge single-coil-sized humbucker (both coils) in parallel.
Position 2 · pull: bridge split + middle splitLegend: when push/pull is UP all pickups are true single coils.Middle Strat Stack Plus (split to one coil) and Bridge single-coil-sized humbucker (split to one coil) in parallel.
Position 3 · push: middleLegend: when push/pull is DOWN all pickups are hum-cancelling.Middle Strat Stack Plus (both coils).
Position 3 · pull: middle splitLegend: when push/pull is UP all pickups are true single coils.Middle Strat Stack Plus (split to one coil).
Position 4 · push: middle + neckLegend: when push/pull is DOWN all pickups are hum-cancelling.Neck Strat Stack Plus (both coils) and Middle Strat Stack Plus (both coils) in parallel.
Position 4 · pull: middle split + neck splitLegend: when push/pull is UP all pickups are true single coils.Neck Strat Stack Plus (split to one coil) and Middle Strat Stack Plus (split to one coil) in parallel.
Position 5 · push: neckLegend: when push/pull is DOWN all pickups are hum-cancelling.Neck Strat Stack Plus (both coils).
Position 5 · pull: neck splitLegend: when push/pull is UP all pickups are true single coils.Neck Strat Stack Plus (split to one coil).

Not simulated: this circuit is drawn for reference only.

  • The sheet prints no pot values; 250k stand-ins are used.
  • There is no three-throw push/pull: the '3 coil split' is one DPDT push/pull whose right pole grounds the middle red directly and whose left pole grounds the blade's second-pole common, which reaches the bridge red & white in positions 1-2 and the neck red in positions 4-5.
  • The blade's second-pole lugs are unlabelled and mapped by function: the reading that reproduces the legend (the lug next to that pole's common is live in positions 1-2, the last lug in positions 4-5). The published Everything Axe references read the same blade drawing's second pole the other way round; under that reading this sheet would ground the bridge and neck links only in positions where those pickups are off, contradicting the legend.
  • The legend's 'all three stacks' wording does not fit this sheet's two stacks and one single-coil-sized humbucker; it is quoted as printed.
  • The on-board component drawn across the bottom-coil pads of each Strat Stack Plus (no value printed) is not modelled.
  • The single-coil-sized bridge humbucker is drawn as the Little '59 SL59-1 (Strat-size); hum cancelling and phase follow its lead colours and coil polarity as Seymour Duncan publishes them.
  • Which shaft position grounds the push/pull's commons follows the usual push/pull behaviour (pulled joins the middle lugs to the lugs nearest the pot); the legend agrees that UP is the split setting.
  • Pickup resistance is not specified, so no numeric meter readings are given.

Before you solder

Ticks are kept in this browser only, as a reminder. They are not a check of your joints. New to soldering? Read the soldering cheat sheet .

Check before plugging in

  • Knob down: in each blade position the meter across the jack reads the full pickup or pickup pair selected.
  • Knob up: the middle red reads ground in every blade position.
  • Knob up, blade in position 1 or 2: the bridge red & white read ground and the neck red reads open; in positions 4 and 5 it is the other way round.

Measure across the output jack with a multimeter on its resistance range. No exact readings are given where the source does not specify the pickups.