Skip to content
Tinkercaster

Seymour Duncan wiring

Two Strat Stack Plus pickups and a single-coil-sized humbucker, 5-way blade, push/pull split volume, two tones

Two Strat Stack Plus · Single-coil-sized humbucker (bridge) · 5-way blade · Push/pull volume (3 coil split) · Two tones

Seymour Duncan sheet: Strat Stack Plus pickups in the neck and middle and a single-coil-sized humbucker in the bridge, on a 5-way blade with a push/pull volume titled '3 coil split' and two tones sharing one .047 cap. The sheet prints no pot values. Pull the knob and each selected pickup drops to one coil: the middle red is grounded through the push/pull's right pole, the bridge red & white and the neck red through the blade's second pole and the push/pull's left pole.

Viewed from the back of the controls, as you solder them.

Two Strat Stack Plus pickups and a single-coil-sized humbucker, 5-way blade, push/pull split volume, two tonesTwo Strat Stack Plus pickups and a single-coil-sized humbucker, 5-way blade, push/pull split volume, two tones: Two Strat Stack Plus · Single-coil-sized humbucker (bridge) · 5-way blade · Push/pull volume (3 coil split) · Two tones. Original Tinkercaster drawing with labelled terminals.Neck Strat Stack PlusMiddle Strat Stack PlusBridge single coil sized humbucker250k250k250k47nFwhiteredblackbarewhiteredblackbareblackgreenwhiteredbareT1T2T3T4T5T6T7T8lug1lug2lug3sw1sw2sw3sw4sw5sw6lug1lug2lug3lug1lug2lug3abtipsleevegroundNeck Strat Stack PlusMiddle Strat Stack PlusBridge single coil sized humbucker5-way bladeVolume (push/pull 3 coil split) · 250kTone (neck lug) · 250kTone (middle lug) · 250k.047 cap · 47nFOutput jackGround wire to bridge

Open the interactive diagram to zoom, move components and try the switches.

Parts and values

In the drawingValuePart
Neck Strat Stack Plus—Strat Stack PlusExample part
Middle Strat Stack Plus—Strat Stack PlusExample part
Bridge single coil sized humbucker—Little '59 SL59-1 Bridge (Strat-size)Example partSame wiring for JB Jr. SJBJ-1 Bridge (Strat-size), Hot Rails SHR-1 Bridge (Strat-size)
5-way blade—Oak Grigsby 5-WayExample part
Volume (push/pull 3 coil split)Source: Volume push/pull (3 coil split)250kNot on the sheet; stand-in250k Push-Pull DPDTExample part
Tone (neck lug)Source: Tone fed from the neck lug (with the .047 cap)250kNot on the sheet; stand-inCTS 250k Audio PotExample part
Tone (middle lug)Source: Tone fed from the middle lug250kNot on the sheet; stand-inCTS 250k Audio PotExample part
.047 cap47nFOrange Drop .047µFExample part
Output jackSource: Output Jack—Switchcraft #11Example part
Ground wire to bridge—Bridge ground wireGeneric

Every pickup is the maker's own. “As specified” means the sheet names that part. “Example part” means the sheet names no model: the pickup shown is one of the maker's with the same leads, and any pot, cap or switch with the same value and lugs will do. “Generic” is a plain part such as a ground wire. “Not on the sheet; stand-in” means the sheet prints no value for that part, so the value shown is the usual one, not the maker's.

Understand this wiring

All Seymour Duncan wiring guides →

Connections

In soldering order: grounds first, then the switch, the pickups and the signal path.

#FromToHow
1Push/pull left lug nearest the potVolume casing (Solder spot)To a pot casingblack
2Neck blackVolume casing (upper Solder spot)To a pot casingblack
3Neck drainVolume casing (upper Solder spot)Drawn gold.Shield or groundbare
4Middle blackVolume casing (upper Solder spot)To a pot casingblack
5Middle drainVolume casing (upper Solder spot)Drawn gold.Shield or groundbare
6Bridge greenVolume casing (upper Solder spot)To a pot casinggreen
7Bridge bareVolume casing (upper Solder spot)Drawn grey beside the green.Shield or groundbare
8Ground wire to bridgeVolume casingTo a pot casingblack
9Volume third lugVolume casingLug bent onto the casing under the lower Solder spot.To a pot casing
10.047 capFirst tone casing (Solder spot)To a pot casing
11First tone casing (Solder spot)Volume casing (lower Solder spot)To a pot casingblack
12Volume casing (lower Solder spot)Jack sleeveWireblack
13Second tone casing (Solder spot)First tone casing (Solder spot)To a pot casingblack
14Bridge blackBlade first row, first lugLabelled 'bridge black'.Wireblack
15Middle whiteBlade first row, second lugLabelled 'middle white'; the inner white loop.Wirewhite
16Neck whiteBlade first row, third lugLabelled 'neck white'; the outer white loop.Wirewhite
17Blade first row, fourth lugVolume first lugWireblack
18Bridge redBlade second row, second lugRuns beside the bridge white to the same lug.Wirered
19Bridge whiteBlade second row, second lugRuns beside the bridge red to the same lug.Wirewhite
20Neck redBlade second row, fourth lugWirered
21Blade second row, first lugPush/pull left middle lugCarries the hops where it crosses the pickup leads.Wireblack
22Blade first row, third lugFirst tone middle lugWireblack
23Blade first row, second lugSecond tone outer lugHops over the neck white.Wireblack
24Middle redPush/pull right middle lugWirered
25Push/pull left lug nearest the potPush/pull right lug nearest the potShort jumper.Wireblack
26Volume middle lugJack tipCarries a hop over the ground wires below the volume.Wireblack
27First tone outer lug.047 capWireblack
28Second tone middle lugFirst tone outer lug (cap lug)Short jumper.Wireblack

What each position does

SettingThe sourceEngine result
Position 1 · push: bridgeLegend: when push/pull is DOWN all pickups are hum-cancelling.Bridge single coil sized humbucker (both coils).
Position 1 · pull: bridge splitLegend: when push/pull is UP all pickups are true single coils.Bridge single coil sized humbucker (split to one coil).
Position 2 · push: bridge + middleLegend: when push/pull is DOWN all pickups are hum-cancelling.Middle Strat Stack Plus (both coils) and Bridge single coil sized humbucker (both coils) in parallel.
Position 2 · pull: bridge split + middle splitLegend: when push/pull is UP all pickups are true single coils.Middle Strat Stack Plus (split to one coil) and Bridge single coil sized humbucker (split to one coil) in parallel.
Position 3 · push: middleLegend: when push/pull is DOWN all pickups are hum-cancelling.Middle Strat Stack Plus (both coils).
Position 3 · pull: middle splitLegend: when push/pull is UP all pickups are true single coils.Middle Strat Stack Plus (split to one coil).
Position 4 · push: middle + neckLegend: when push/pull is DOWN all pickups are hum-cancelling.Neck Strat Stack Plus (both coils) and Middle Strat Stack Plus (both coils) in parallel.
Position 4 · pull: middle split + neck splitLegend: when push/pull is UP all pickups are true single coils.Neck Strat Stack Plus (split to one coil) and Middle Strat Stack Plus (split to one coil) in parallel.
Position 5 · push: neckLegend: when push/pull is DOWN all pickups are hum-cancelling.Neck Strat Stack Plus (both coils).
Position 5 · pull: neck splitLegend: when push/pull is UP all pickups are true single coils.Neck Strat Stack Plus (split to one coil).

Not simulated: this circuit is drawn for reference only.

  • The sheet prints no pot values; 250k stand-ins are used.
  • There is no three-throw push/pull: the '3 coil split' is one DPDT push/pull whose right pole grounds the middle red directly and whose left pole grounds the blade's second-pole common, which reaches the bridge red & white in positions 1-2 and the neck red in positions 4-5.
  • The legend's 'all three stacks' wording does not fit this sheet's two stacks and one single-coil-sized humbucker; it is quoted as printed.
  • The on-board component drawn across the bottom-coil pads of each Strat Stack Plus (no value printed) is not modelled.
  • The single-coil-sized bridge humbucker is drawn as the Little '59 SL59-1 (Strat-size); hum cancelling and phase follow its lead colours and coil polarity as Seymour Duncan publishes them.
  • Which shaft position grounds the push/pull's commons follows the usual push/pull behaviour (pulled joins the middle lugs to the lugs nearest the pot); the legend agrees that UP is the split setting.
  • Pickup resistance is not specified, so no numeric meter readings are given.

Before you solder

Ticks are kept in this browser only, as a reminder. They are not a check of your joints. New to soldering? Read the soldering cheat sheet .

Check before plugging in

  • Knob down: in each blade position the meter across the jack reads the full pickup or pickup pair selected.
  • Knob up: the middle red reads ground in every blade position; the bridge red & white read ground in positions 1-2 and the neck red in positions 4-5.
  • Neck tone: acts in positions 4 and 5; middle tone: acts in positions 2 to 4, through the shared .047 cap.

Measure across the output jack with a multimeter on its resistance range. No exact readings are given where the source does not specify the pickups.