Parts and values
| In the drawing | Value | Part |
|---|---|---|
| Neck Strat Stack Plus | — | Strat Stack Plus |
| Middle Strat Stack Plus | — | Strat Stack Plus |
| Bridge Strat Stack Plus | — | Strat Stack Plus |
| 5-way super-switch | — | Oak Grigsby 4-Pole 5-Way Super Switch |
| Master volume 250k | 250k | CTS 250k Audio Pot |
| Output Jack | — | Switchcraft #11 |
| Ground wire to bridge | — | Bridge ground wire |
| Tone 250k (upper, neck) | 250k | CTS 250k Audio Pot |
| Tone 250k (lower, middle) | 250k | CTS 250k Audio Pot |
| .022 tone cap | 22nF | Orange Drop .022µF |
Every pickup is the maker's own. “As specified” means the sheet names that part. “Example part” means the sheet names no model: the pickup shown is one of the maker's with the same leads, and any pot, cap or switch with the same value and lugs will do. “Generic” is a plain part such as a ground wire. “Not on the sheet; stand-in” means the sheet prints no value for that part, so the value shown is the usual one, not the maker's.
Connections
In soldering order: grounds first, then the switch, the pickups and the signal path.
| # | From | To | How |
|---|---|---|---|
| 1 | Right wafer lug 1 (top) | Volume casing (lower Solder spot) | To a pot casing |
| 2 | Right wafer lug 12 (bottom) | Volume casing (upper Solder spot) | To a pot casing |
| 3 | Neck black | Volume casing (upper Solder spot) | To a pot casing |
| 4 | Neck bare (drain) | Volume casing (upper Solder spot) | To a pot casing |
| 5 | Middle black | Volume casing (upper Solder spot) | To a pot casing |
| 6 | Middle bare (drain) | Volume casing (upper Solder spot) | To a pot casing |
| 7 | Bridge black | Volume casing (upper Solder spot) | To a pot casing |
| 8 | Bridge bare (drain) | Volume casing (upper Solder spot) | To a pot casing |
| 9 | Ground wire to bridge | Volume casing (upper Solder spot) | To a pot casing |
| 10 | Volume third lug | Volume casing (lower Solder spot) | To a pot casing |
| 11 | Volume casing (lower Solder spot) | Jack sleeve | To a pot casing |
| 12 | .022 cap | Upper tone casing (Solder spot) | To a pot casing |
| 13 | Upper tone casing (Solder spot) | Volume casing (lower Solder spot) | To a pot casing |
| 14 | Lower tone casing (Solder spot) | Upper tone casing (Solder spot) | To a pot casing |
| 15 | Bridge white | Left wafer lug 7 | Wire |
| 16 | Left wafer lug 7 | Left wafer lug 8 | Wire |
| 17 | Middle white | Left wafer lug 3 | Wire |
| 18 | Left wafer lug 3 | Left wafer lug 4 | Wire |
| 19 | Left wafer lug 4 | Left wafer lug 5 | Wire |
| 20 | Neck white | Left wafer lug 10 | Wire |
| 21 | Left wafer lug 10 | Left wafer lug 11 | Wire |
| 22 | Middle red | Right wafer lug 3 | Wire |
| 23 | Right wafer lug 3 | Right wafer lug 5 | Wire |
| 24 | Bridge red | Right wafer lug 8 | Wire |
| 25 | Neck red | Right wafer lug 10 | Wire |
| 26 | Left wafer lug 1 (top) | Left wafer lug 12 (bottom) | Wire |
| 27 | Left wafer lug 12 (bottom) | Volume first lug | Wire |
| 28 | Left wafer lug 11 | Upper tone middle lug | Wire |
| 29 | Left wafer lug 5 | Lower tone first lug | Wire |
| 30 | Volume middle lug | Jack tip | Wire |
| 31 | Upper tone third lug | .022 cap | Wire |
| 32 | Lower tone middle lug | Upper tone third lug | Wire |
What each position does
| Setting | The source | Engine result |
|---|---|---|
| Bridge full stack | — | Bridge Strat Stack Plus (both coils). |
| Bridge split + middle split | — | Middle Strat Stack Plus (split to one coil) and Bridge Strat Stack Plus (split to one coil) in parallel. |
| Middle full stack | — | Middle Strat Stack Plus (both coils). |
| Neck split + middle split | — | Neck Strat Stack Plus (split to one coil) and Middle Strat Stack Plus (split to one coil) in parallel. |
| Neck full stack | — | Neck Strat Stack Plus (both coils). |
Checked with the Tinkercaster wiring engine against the switching the source describes.
- The small component printed across each Strat Stack Plus board's lower-coil pads is not modelled; the sheet prints no value for it.
- Pickup resistance is not specified, so no numeric meter readings are given.
Before you solder
Ticks are kept in this browser only, as a reminder. They are not a check of your joints. New to soldering? Read the soldering cheat sheet .
Check before plugging in
- In positions 1, 3 and 5 the meter across the jack should read one whole stack; in positions 2 and 4 two split stacks in parallel.
- With the volume at zero, tip and sleeve should read as a short.
- The upper tone should act whenever the neck pickup is selected (positions 4 and 5) and the lower tone whenever the middle pickup is selected (positions 2, 3 and 4).
Measure across the output jack with a multimeter on its resistance range. No exact readings are given where the source does not specify the pickups.