Skip to content
Tinkercaster

Seymour Duncan wiring

Two humbuckers, toggle, mini-toggle phase, volume

Two humbuckers · Three-way toggle · Mini-toggle phase · One volume

Transcribed from the manufacturer wiring sheet and checked against the engine.

Viewed from the back of the controls, as you solder them.

Two humbuckers, toggle, mini-toggle phase, volumeTwo humbuckers, toggle, mini-toggle phase, volume: Two humbuckers · Three-way toggle · Mini-toggle phase · One volume. Original Tinkercaster drawing with labelled terminals.Neck PickupBridge Pickup500kblackgreenwhiteredbareblackgreenwhiteredbareT1T2T3T4T1T2T3T4T5T6lug1lug2lug3tipsleevegroundNeck PickupBridge Pickup3-Way TogglePhase switch ON/ON mini-toggleVolume 500kOutput JackBridge ground

Open the interactive diagram to zoom, move components and try the switches.

Parts and values

In the drawingValuePart
Neck Pickup—'59 Model SH-1 NeckExample partSame wiring for Jazz Model SH-2 Neck, Duncan Distortion SH-6 Neck, Invader SH-8 Neck, Seymour Duncan Antiquity Neck, Alnico II Pro APH-1 Neck, Pearly Gates SH-PG1 Neck
Bridge Pickup—JB Model SH-4Example partSame wiring for '59 Model SH-1 Bridge, Duncan Custom SH-5, Duncan Distortion SH-6 Bridge, Invader SH-8 Bridge, Custom Five SH-14, Seymour Duncan SH-2 Jazz Bridge
3-Way Toggle—Switchcraft 3-Way ToggleExample part
Phase switch ON/ON mini-toggle—DPDT Mini-ToggleExample part
Volume 500k500kCTS 500k Audio PotExample part
Output Jack—Switchcraft #11Example part
Bridge ground—Bridge ground wireGeneric

Every pickup is the maker's own. “As specified” means the sheet names that part. “Example part” means the sheet names no model: the pickup shown is one of the maker's with the same leads, and any pot, cap or switch with the same value and lugs will do. “Generic” is a plain part such as a ground wire. “Not on the sheet; stand-in” means the sheet prints no value for that part, so the value shown is the usual one, not the maker's.

Understand this wiring

All Seymour Duncan wiring guides →

Connections

In soldering order: grounds first, then the switch, the pickups and the signal path.

#FromToHow
1Bridge Pickup gndVolume 500k casingWiregreen
2Neck Pickup bareVolume 500k casingWirebare
3Bridge Pickup bareVolume 500k casingWirebare
4Neck Pickup gndPhase switch ON/ON mini-toggle T5Wiregreen
5Phase switch ON/ON mini-toggle T3Volume 500k casingWireblack
63-Way Toggle T4Volume 500k casingWireblack
7Volume 500k lug1Volume 500k casingWireground
8Volume 500k casingOutput Jack sleeveWireblack
9Bridge ground groundVolume 500k casingWireblack
10Bridge Pickup hot3-Way Toggle T2Wireblack
11Neck Pickup hotPhase switch ON/ON mini-toggle T2Wireblack
12Phase switch ON/ON mini-toggle T1Phase switch ON/ON mini-toggle T6Wireblack
13Phase switch ON/ON mini-toggle T4Phase switch ON/ON mini-toggle T3Wireblack
14Phase switch ON/ON mini-toggle T13-Way Toggle T1Wireblack
153-Way Toggle T3Volume 500k lug3Wireblack
16Neck Pickup redNeck Pickup whiteWirered
17Bridge Pickup redBridge Pickup whiteWirered
18Volume 500k lug2Output Jack tipWireblack

What each position does

SettingThe sourceEngine result
Rhythm (neck)Engine reading of the transcribed board; matches the source legend.Neck Pickup (both coils).
BothEngine reading of the transcribed board; matches the source legend.Neck Pickup (both coils) and Bridge Pickup (both coils) in parallel.
Treble (bridge)Engine reading of the transcribed board; matches the source legend.Bridge Pickup (both coils).

Checked with the Tinkercaster wiring engine against the switching the source describes.

Before you solder

Ticks are kept in this browser only, as a reminder. They are not a check of your joints. New to soldering? Read the soldering cheat sheet .

Check before plugging in

    Measure across the output jack with a multimeter on its resistance range. No exact readings are given where the source does not specify the pickups.