Skip to content
Tinkercaster

Seymour Duncan wiring

Two single coils and a single coil sized humbucker, 5-way blade, push/pull coil-split volume

Two single coils · Single coil sized humbucker (bridge) · 5-way blade · One push/pull volume (coil split)

Seymour Duncan sheet: neck and middle single coils with a single coil sized humbucker in the bridge on a 5-way blade. The volume's push/pull grounds the humbucker's red & white when pulled, splitting it.

Viewed from the back of the controls, as you solder them.

Two single coils and a single coil sized humbucker, 5-way blade, push/pull coil-split volumeTwo single coils and a single coil sized humbucker, 5-way blade, push/pull coil-split volume: Two single coils · Single coil sized humbucker (bridge) · 5-way blade · One push/pull volume (coil split). Original Tinkercaster drawing with labelled terminals.Neck single coilMiddle single coilBridge single coil sized humbucker250kwhiteblackwhiteblackblackgreenwhiteredbareT1T2T3T4T5T6T7T8lug1lug2lug3sw1sw2sw3sw4sw5sw6tipsleevegroundNeck single coilMiddle single coilBridge single coil sized humbucker5-way bladeVolume push/pull (value not printed) · 250kOutput jackGround wire to bridge

Open the interactive diagram to zoom, move components and try the switches.

Parts and values

In the drawingValuePart
Neck single coil—Vintage Staggered Strat SSL-1Example partSame wiring for Vintage Flat Strat SSL-2, Quarter-Pound Flat Strat SSL-4, Alnico II Pro Staggered Strat APS-1
Middle single coil—Vintage Staggered Strat SSL-1Example partSame wiring for Vintage Flat Strat SSL-2, Quarter-Pound Flat Strat SSL-4, Alnico II Pro Staggered Strat APS-1
Bridge single coil sized humbuckerSource: Single coil sized humbucker (bridge)—Little '59 SL59-1 Bridge (Strat-size)Example partSame wiring for JB Jr. SJBJ-1 Bridge (Strat-size), Hot Rails SHR-1 Bridge (Strat-size)
5-way bladeSource: 5 way blade—Oak Grigsby 5-WayExample part
Volume push/pull (value not printed)Source: Volume push | pull coil split250kNot on the sheet; stand-in250k Push-Pull DPDTGeneric
Output jackSource: Output Jack—Switchcraft #11Example part
Ground wire to bridge—Bridge ground wireGeneric

Every pickup is the maker's own. “As specified” means the sheet names that part. “Example part” means the sheet names no model: the pickup shown is one of the maker's with the same leads, and any pot, cap or switch with the same value and lugs will do. “Generic” is a plain part such as a ground wire. “Not on the sheet; stand-in” means the sheet prints no value for that part, so the value shown is the usual one, not the maker's.

Understand this wiring

All Seymour Duncan wiring guides →

Connections

In soldering order: grounds first, then the switch, the pickups and the signal path.

#FromToHow
1Push/pull lug nearest the potVolume casing (Solder spot)Black wire from the push/pull lug nearest the pot body (same row) down to the volume Solder spot (mapped sw1, the pulled contact).To a pot casingblack
2SCH greenVolume casing (Solder spot)SCH green leaves the cable to the Solder spot on the volume casing.To a pot casinggreen
3SCH bareVolume casing (Solder spot)SCH bare (drawn grey beside the green) to the same Solder spot.Shield or groundbare
4Neck blackVolume casing (Solder spot)Neck single-coil black runs straight down to the volume Solder spot.To a pot casingblack
5Middle blackVolume casing (Solder spot)Middle single-coil black runs straight down to the volume Solder spot.To a pot casingblack
6Ground wire to bridgeVolume casing (Solder spot)'Ground wire to bridge' leaves the volume Solder spot (arrow).To a pot casingblack
7Volume bottom lugVolume casing (Solder spot)The volume's bottom lug is bent onto the casing under the Solder spot.To a pot casing
8Volume casing (Solder spot)Jack sleeveBlack wire from the volume Solder spot to the jack Sleeve (ground); it carries the hop over the tip wire.To a pot casingblack
9SCH blackSwitch upper row, fourth lugSCH black leaves the cable, arcs up over the controls and lands on the upper-row lug at the far end from the common (mapped T3, bridge throw, positions 1-2).Wireblack
10Middle whiteSwitch upper row, third lugMiddle single-coil white runs in the lower of the two white leads to the third upper-row lug from the common (mapped T1, positions 2-4).Wirewhite
11Neck whiteSwitch upper row, second lugNeck single-coil white passes the middle pickup and runs as the outer white lead to the upper-row lug next to the common (mapped T2, positions 4-5).Wirewhite
12Switch upper row, first lugSwitch lower row, fourth lugWhite jumper from the upper-row end lug (the common) along under the row to the opposite-row lug at the far end (mapped T8, the second pole's common, diagonally opposite).Wirewhite
13Switch lower row, fourth lugVolume top lugWhite wire from that opposite-row end lug down to the volume's top lug (input).Wirewhite
14SCH whitePush/pull middle lugSCH white leaves the cable beside the red and lands on the push/pull's middle lug of the row nearest the SCH (mapped sw2, pole A common).Wirewhite
15SCH redPush/pull middle lugSCH red lands on the same push/pull middle lug with the white.Wirered
16Volume middle lugJack tipWhite wire from the volume's middle lug down to the jack Tip (hot output).Wirewhite

What each position does

SettingThe sourceEngine result
Bridge · pushedThe sheet prints no position legend; this is the standard 5-way contact table with the lugs mapped by function.Bridge single coil sized humbucker (both coils).
Bridge · pulledThe sheet prints no position legend; this is the standard 5-way contact table with the lugs mapped by function. Pulled grounds the SCH red & white ('push | pull coil split').Bridge single coil sized humbucker (split to one coil).
Bridge + middle · pushedThe sheet prints no position legend; this is the standard 5-way contact table with the lugs mapped by function.Middle single coil and Bridge single coil sized humbucker (both coils) in parallel.
Bridge + middle · pulledThe sheet prints no position legend; this is the standard 5-way contact table with the lugs mapped by function. Pulled grounds the SCH red & white ('push | pull coil split').Middle single coil and Bridge single coil sized humbucker (split to one coil) in parallel.
Middle · pushedThe sheet prints no position legend; this is the standard 5-way contact table with the lugs mapped by function.Middle single coil.
Middle · pulledThe sheet prints no position legend; this is the standard 5-way contact table with the lugs mapped by function. The SCH is not selected, so pulling changes nothing here.Middle single coil.
Middle + neck · pushedThe sheet prints no position legend; this is the standard 5-way contact table with the lugs mapped by function.Neck single coil and Middle single coil in parallel.
Middle + neck · pulledThe sheet prints no position legend; this is the standard 5-way contact table with the lugs mapped by function. The SCH is not selected, so pulling changes nothing here.Neck single coil and Middle single coil in parallel.
Neck · pushedThe sheet prints no position legend; this is the standard 5-way contact table with the lugs mapped by function.Neck single coil.
Neck · pulledThe sheet prints no position legend; this is the standard 5-way contact table with the lugs mapped by function. The SCH is not selected, so pulling changes nothing here.Neck single coil.

Not simulated: this circuit is drawn for reference only.

  • The sheet prints no pot values; 250k stand-ins are used.
  • The single-coil-sized humbucker is drawn as the Little '59 SL59-1 (Strat-size); hum cancelling and phase follow its lead colours and coil polarity as Seymour Duncan publishes them.
  • The sheet does not say which knob position splits beyond 'push | pull coil split'; this follows the usual push/pull behaviour (pulled joins the middle lugs to the lugs nearest the pot).
  • Pickup resistance is not specified, so no numeric meter readings are given.

Before you solder

Ticks are kept in this browser only, as a reminder. They are not a check of your joints. New to soldering? Read the soldering cheat sheet .

Check before plugging in

  • Knob pushed: positions 1 and 2 read the full humbucker.
  • Knob pulled: positions 1 and 2 read one humbucker coil; the red & white read ground.

Measure across the output jack with a multimeter on its resistance range. No exact readings are given where the source does not specify the pickups.