TinkercasterParts and values
| In the drawing | Value | Part |
|---|---|---|
| Neck single coil | — | Single-coil pickup (two-conductor)Generic |
| Middle single coil | — | Single-coil pickup (two-conductor)Generic |
| Bridge single coil sized humbuckerSource: Single coil sized humbucker (bridge) | — | Humbucker (four-conductor, Seymour Duncan colours)Generic |
| 5-way bladeSource: 5 way blade | — | Oak Grigsby 5-WayExample part |
| Volume push/pull (value not printed)Source: Volume push/pull coil split | 250k | 250k Push-Pull DPDTGeneric |
| Output jackSource: Output Jack | — | Switchcraft #11Example part |
| Ground wire to bridge | — | Bridge ground wireGeneric |
| Tone 1 (value not printed)Source: Tone 1 (nearer the volume) | 250k | CTS 250k Audio PotGeneric |
| .047 cap | 47nF | Orange Drop .047µFExample part |
| Tone 2 (value not printed)Source: Tone 2 | 250k | CTS 250k Audio PotGeneric |
“Example part” means any part with the same value and lugs will do; the source does not name a brand. “Generic” stands in for an unspecified pickup: check your own pickup's lead colours before you solder.
Specific to this wiring
- Solder = location for ground (earth) connections.
- Jack: Tip (hot output); Sleeve (ground). The inner, circular portion of the jack.
- Ground wire to bridge.
- The sheet prints no position legend and does not number the switch lugs; the lugs are mapped by what they do (see the terminal mapping).
- 1 volume: push/pull coil split. 2 tone.
- The tone cap is printed '.047 cap'; tone 2 reaches it through a wire to tone 1's cap lug.
Understand this wiring
- Seymour Duncan humbucker wire colors
See the pickup, recognise its two halves, and learn where each coloured wire goes.
- Seymour Duncan coil splitting explained
A humbucker has two coils. See how a switch lets you use just one of them.
Connections
In soldering order: grounds first, then the switch, the pickups and the signal path.
| # | From | To | How |
|---|---|---|---|
| 1 | Push/pull lug nearest the pot | Volume casing (Solder spot)Black wire from the push/pull lug nearest the pot body (same row) down to the volume Solder spot (mapped sw1, the pulled contact). | To a pot casingblack |
| 2 | SCH green | Volume casing (Solder spot)SCH green leaves the cable to the Solder spot on the volume casing. | To a pot casinggreen |
| 3 | SCH bare | Volume casing (Solder spot)SCH bare (drawn grey beside the green) to the same Solder spot. | Shield or groundbare |
| 4 | Neck black | Volume casing (Solder spot)Neck single-coil black runs straight down to the volume Solder spot. | To a pot casingblack |
| 5 | Middle black | Volume casing (Solder spot)Middle single-coil black runs straight down to the volume Solder spot. | To a pot casingblack |
| 6 | Ground wire to bridge | Volume casing (Solder spot)'Ground wire to bridge' leaves the volume Solder spot (arrow). | To a pot casingblack |
| 7 | Volume bottom lug | Volume casing (Solder spot)The volume's bottom lug is bent onto the casing under the Solder spot. | To a pot casing |
| 8 | Volume casing (Solder spot) | Jack sleeveBlack wire from the volume Solder spot to the jack Sleeve (ground); it carries the hop over the tip wire. | To a pot casingblack |
| 9 | .047 cap | Tone 1 casing (Solder spot)The cap's other lead to the Solder spot on the tone 1 casing. | To a pot casingblack |
| 10 | Tone 2 casing (Solder spot) | Tone 1 casing (Solder spot)Black wire from the tone 2 Solder spot up to the tone 1 Solder spot. | To a pot casingblack |
| 11 | Tone 1 casing (Solder spot) | Volume casing (Solder spot)Black wire from the tone 1 Solder spot, hopping over the tip wire, to the volume Solder spot. | To a pot casingblack |
| 12 | SCH black | Switch upper row, fourth lugSCH black leaves the cable, arcs up over the controls and lands on the upper-row lug at the far end from the common (mapped T3, bridge throw, positions 1-2). | Wireblack |
| 13 | Middle white | Switch upper row, third lugMiddle single-coil white runs in the lower of the two white leads to the third upper-row lug from the common (mapped T1, positions 2-4). | Wirewhite |
| 14 | Neck white | Switch upper row, second lugNeck single-coil white passes the middle pickup and runs as the outer white lead to the upper-row lug next to the common (mapped T2, positions 4-5). | Wirewhite |
| 15 | Switch upper row, first lug | Switch lower row, fourth lugWhite jumper from the upper-row end lug (the common) along under the row to the opposite-row lug at the far end (mapped T8, the second pole's common, diagonally opposite). | Wirewhite |
| 16 | Switch lower row, fourth lug | Volume top lugWhite wire from that opposite-row end lug down to the volume's top lug (input). | Wirewhite |
| 17 | Switch lower row, first lug | Tone 1 middle lugWhite wire from the opposite-row end lug farthest from that row's common (mapped T7, positions 1-2) down to tone 1's middle lug; it passes under the tone-2 feed. | Wirewhite |
| 18 | Switch lower row, second lug | Tone 2 upper outer lugWhite wire from the opposite-row second lug from the common (mapped T5, positions 2-4); it carries the hop over the tone-1 feed and loops round the outside to tone 2's outer lug (tone 2 drawn lugs up; mapped lug1). | Wirewhite |
| 19 | SCH white | Push/pull middle lugSCH white leaves the cable beside the red and lands on the push/pull's middle lug of the row nearest the SCH (mapped sw2, pole A common). | Wirewhite |
| 20 | SCH red | Push/pull middle lugSCH red lands on the same push/pull middle lug with the white. | Wirered |
| 21 | Volume middle lug | Jack tipWhite wire from the volume's middle lug down to the jack Tip (hot output). | Wirewhite |
| 22 | Tone 1 lower outer lug | .047 capBlack lead from tone 1's lower outer lug (tone 1 drawn with its lugs pointing down-left; mapped lug1) to the .047 cap. | Wireblack |
| 23 | Tone 2 middle lug | Tone 1 lower outer lugWhite wire from tone 2's middle lug to tone 1's lug that carries the cap (shared cap). | Wirewhite |
What each position does
| Setting | The source | Engine result |
|---|---|---|
| Bridge · pushed | The sheet prints no position legend; this is the standard 5-way contact table with the lugs mapped by function. | Bridge single coil sized humbucker (both coils). |
| Bridge · pulled | The sheet prints no position legend; this is the standard 5-way contact table with the lugs mapped by function. Pulled grounds the SCH red & white ('push/pull coil split'). | Bridge single coil sized humbucker (split to one coil). |
| Bridge + middle · pushed | The sheet prints no position legend; this is the standard 5-way contact table with the lugs mapped by function. | Middle single coil and Bridge single coil sized humbucker (both coils) in parallel. |
| Bridge + middle · pulled | The sheet prints no position legend; this is the standard 5-way contact table with the lugs mapped by function. Pulled grounds the SCH red & white ('push/pull coil split'). | Middle single coil and Bridge single coil sized humbucker (split to one coil) in parallel. |
| Middle · pushed | The sheet prints no position legend; this is the standard 5-way contact table with the lugs mapped by function. | Middle single coil. |
| Middle · pulled | The sheet prints no position legend; this is the standard 5-way contact table with the lugs mapped by function. The SCH is not selected, so pulling changes nothing here. | Middle single coil. |
| Middle + neck · pushed | The sheet prints no position legend; this is the standard 5-way contact table with the lugs mapped by function. | Neck single coil and Middle single coil in parallel. |
| Middle + neck · pulled | The sheet prints no position legend; this is the standard 5-way contact table with the lugs mapped by function. The SCH is not selected, so pulling changes nothing here. | Neck single coil and Middle single coil in parallel. |
| Neck · pushed | The sheet prints no position legend; this is the standard 5-way contact table with the lugs mapped by function. | Neck single coil. |
| Neck · pulled | The sheet prints no position legend; this is the standard 5-way contact table with the lugs mapped by function. The SCH is not selected, so pulling changes nothing here. | Neck single coil. |
Not simulated: this circuit is drawn for reference only.
- The sheet prints no pot values; 250k stand-ins are used.
- The single coil sized humbucker is modelled by a generic four-conductor humbucker; hum cancelling and phase describe the generic model.
- The sheet does not say which knob position splits beyond 'push/pull coil split'; this follows the usual push/pull behaviour (pulled joins the middle lugs to the lugs nearest the pot).
- Which positions each tone works in follows the by-function lug mapping of the switch's second pole; the sheet does not label it.
- Pickup resistance is not specified, so no numeric meter readings are given.
Before you solder
Ticks are kept in this browser only, as a reminder. They are not a check of your joints. New to soldering? Read the soldering cheat sheet.
Check before plugging in
- Knob pushed: positions 1 and 2 read the full humbucker.
- Knob pulled: positions 1 and 2 read one humbucker coil; the red & white read ground.
Measure across the output jack with a multimeter on its resistance range. No exact readings are given where the source does not specify the pickups.