Skip to content
Tinkercaster

Tonerider wiring

One humbucker with one volume and one tone

One humbucker · No switch · One volume · One tone

A four-conductor humbucker in series through a 500kA volume and a 500kA tone with a .022 µF capacitor, to a mono jack. Tonerider draws it for all its four-conductor AC and H series humbuckers.

Viewed from the back of the controls, as you solder them.

One humbucker with one volume and one toneOne humbucker with one volume and one tone: One humbucker · No switch · One volume · One tone. Original Tinkercaster drawing with labelled terminals.Humbucker500k500k22nFredblackwhitegreenbarelug1lug2lug3lug1lug2lug3abtipsleevegroundHumbuckerVolume 500kATone 500kA.022µfOutput jackBridge ground

Open the interactive diagram to zoom, move components and try the switches.

Parts and values

In the drawingValuePart
HumbuckerSource: Humbucker (red, green, black, white, bare)—Tonerider Alnico 2 ClassicExample partSame wiring for Tonerider Alnico 4 Classic, Tonerider Rocksong
Volume 500kA500kCTS 500k Audio PotExample part
Tone 500kA500kCTS 500k Audio PotExample part
.022µfSource: .022µf capacitor (drawn orange)22nFOrange Drop .022µFExample part
Output jackSource: Output Jack—Switchcraft #11Example part
Bridge groundSource: Ground Wire from Bridge—Bridge ground wireGeneric

Every pickup is the maker's own. “As specified” means the sheet names that part. “Example part” means the sheet names no model: the pickup shown is one of the maker's with the same leads, and any pot, cap or switch with the same value and lugs will do. “Generic” is a plain part such as a ground wire. “Not on the sheet; stand-in” means the sheet prints no value for that part, so the value shown is the usual one, not the maker's.

Connections

In soldering order: grounds first, then the switch, the pickups and the signal path.

#FromToHow
1Ground Wire from BridgeVolume casingShield or ground
2Pickup greenVolume casingTo a pot casinggreen
3Bare Shield WireVolume casingShield or groundbare
4Volume right lugVolume casingShort black link.To a pot casing
5Tone casingVolume casingTo a pot casing
6Volume casingJack sleeveGround Wire to Output Jack Sleeve Lug.Wire
7.022µf capacitorTone casingTo a pot casing
8Pickup blackPickup whiteSoldered together and insulated; touches nothing else.Joined and insulatedblack
9Pickup redVolume left lug (input)Wirered
10Volume left lugTone left lugWire
11Tone middle lug.022µf capacitorWire
12Volume middle lugJack tipSignal/Hot Wire to Output Jack Tip Lug.Wire

What it does

Engine result: Humbucker (both coils).

Checked with the Tinkercaster wiring engine against the switching the source describes.

  • Hum cancelling and phase follow the pickups' lead colours and coil polarity as Tonerider publishes them; nothing here is measured.
  • Pickup resistance is not specified, so no numeric meter readings are given.

Before you solder

Ticks are kept in this browser only, as a reminder. They are not a check of your joints. New to soldering? Read the soldering cheat sheet .

Check before plugging in

  • With both pots up, the meter across the jack should read the humbucker's resistance.
  • The taped black–white joint should read about one coil's resistance to ground, roughly half the pickup's total (a few kΩ): not open, and not zero.

Measure across the output jack with a multimeter on its resistance range. No exact readings are given where the source does not specify the pickups.