Parts and values
| In the drawing | Value | Part |
|---|---|---|
| Neck Pickup (P90) | — | Tonerider Hot 90 |
| Bridge Pickup | — | Tonerider Alnico 2 Classic |
| 3-Way Toggle | — | Switchcraft 3-Way Toggle |
| Volume 500kA | 500k | CTS 500k Audio Pot |
| Tone 500kA | 500k | CTS 500k Audio Pot |
| .022µf | 22nF | Orange Drop .022µF |
| Output Jack | — | Switchcraft #11 |
| Ground Wire from Bridge | — | Bridge ground wire |
Every pickup is the maker's own. “As specified” means the sheet names that part. “Example part” means the sheet names no model: the pickup shown is one of the maker's with the same leads, and any pot, cap or switch with the same value and lugs will do. “Generic” is a plain part such as a ground wire. “Not on the sheet; stand-in” means the sheet prints no value for that part, so the value shown is the usual one, not the maker's.
Connections
In soldering order: grounds first, then the switch, the pickups and the signal path.
| # | From | To | How |
|---|---|---|---|
| 1 | Bridge green | Volume casing | To a pot casing |
| 2 | Bridge bare shield | Volume casing | Shield or ground |
| 3 | Neck black and bare shield | Toggle frame lug | Wire |
| 4 | Toggle frame lug | Ground (Volume casing) | To a pot casing |
| 5 | Volume right lug | Volume casing | To a pot casing |
| 6 | .022µf capacitor | Tone casing | To a pot casing |
| 7 | Tone casing | Ground (Volume casing) | To a pot casing |
| 8 | Jack sleeve | Ground (Volume casing) | Wire |
| 9 | Ground Wire from Bridge | Volume casing | To a pot casing |
| 10 | Neck Pickup (P90) bare shield | Toggle frame lug | Shield or ground |
| 11 | Bridge red | Toggle lower outer lug | Wire |
| 12 | Neck white | Toggle upper outer lug | Wire |
| 13 | Toggle middle lug | Volume left lug | Wire |
| 14 | Bridge black | Bridge white | Joined and insulated |
| 15 | Volume middle lug | Jack tip | Wire |
| 16 | Volume left lug | Tone left lug | Wire |
| 17 | Tone middle lug | .022µf capacitor | Wire |
What each position does
| Setting | The source | Engine result |
|---|---|---|
| Neck: P90 | The neck white lead is on the toggle's upper outer lug. | Neck Pickup (P90). |
| Middle: both pickups | Both outer toggle lugs join the middle lug. | Neck Pickup (P90) and Bridge Pickup (both coils) in parallel. |
| Bridge: humbucker | The bridge red lead is on the toggle's lower outer lug; black and white are joined, so both coils run in series. | Bridge Pickup (both coils). |
Checked with the Tinkercaster wiring engine against the switching the source describes.
- The P90 is simulated from its catalog leads (white hot, black ground, bare shield); hum cancelling and phase follow the pickups' lead colours and coil polarity as Tonerider publishes them; nothing here is measured.
- Hum cancelling and phase follow the pickups' lead colours and coil polarity as Tonerider publishes them; nothing here is measured.
- The source does not label the toggle positions; they follow the usual neck, both, bridge order.
- Pickup resistance is not specified, so no numeric meter readings are given.
Before you solder
Ticks are kept in this browser only, as a reminder. They are not a check of your joints. New to soldering? Read the soldering cheat sheet .
Check before plugging in
- In each toggle position the meter across the jack reads the P90, both pickups in parallel, or the full humbucker.
- With the volume at zero, tip and sleeve should read as a short in every position.
Measure across the output jack with a multimeter on its resistance range. No exact readings are given where the source does not specify the pickups.