Skip to content
Tinkercaster

Tonerider wiring

P90 neck and humbucker bridge with a three-way toggle, push/pull split volume and one tone

P90 + humbucker · Three-way toggle · Push/pull volume (bridge split) · One tone

Tonerider's 1 P90, 1 Humbucker, 1 Volume (Push-Pull), 1 Tone harness: a P90 in the neck and a four-conductor humbucker in the bridge on a three-way toggle, then a 500kA push/pull volume and a 500kA tone with a .022 µF capacitor. Pulling the volume knob grounds the bridge black–white link so that pickup splits to the slug coil.

Viewed from the back of the controls, as you solder them.

P90 neck and humbucker bridge with a three-way toggle, push/pull split volume and one toneP90 neck and humbucker bridge with a three-way toggle, push/pull split volume and one tone: P90 + humbucker · Three-way toggle · Push/pull volume (bridge split) · One tone. Original Tinkercaster drawing with labelled terminals.Neck Pickup (P90)Bridge Pickup500k500k22nFwhiteblackbareredblackwhitegreenbareT1T2T3T4lug1lug2lug3sw1sw2sw3sw4sw5sw6lug1lug2lug3abtipsleevegroundNeck Pickup (P90)Bridge Pickup3-Way ToggleVolume 500kA (push-pull)Tone 500kA.022µfOutput JackGround Wire from Bridge

Open the interactive diagram to zoom, move components and try the switches.

Parts and values

In the drawingValuePart
Neck Pickup (P90)—Tonerider Hot 90Example part
Bridge Pickup—Tonerider Alnico 2 ClassicExample partSame wiring for Tonerider Alnico 4 Classic, Tonerider Rocksong
3-Way Toggle—Switchcraft 3-Way ToggleExample part
Volume 500kA (push-pull)500k500k Push-Pull DPDTExample part
Tone 500kA500kCTS 500k Audio PotExample part
.022µfSource: .022µf capacitor (drawn orange)22nFOrange Drop .022µFExample part
Output Jack—Switchcraft #11Example part
Ground Wire from Bridge—Bridge ground wireGeneric

Every pickup is the maker's own. “As specified” means the sheet names that part. “Example part” means the sheet names no model: the pickup shown is one of the maker's with the same leads, and any pot, cap or switch with the same value and lugs will do. “Generic” is a plain part such as a ground wire. “Not on the sheet; stand-in” means the sheet prints no value for that part, so the value shown is the usual one, not the maker's.

Connections

In soldering order: grounds first, then the switch, the pickups and the signal path.

#FromToHow
1Push/pull left lug nearest the potVolume casingTo a pot casingblack
2Bridge greenVolume casingTo a pot casinggreen
3Bridge bare shieldVolume casingSame solder spot as the green lead.Shield or groundbare
4Neck black and bare shieldToggle frame lugThe black lead and the bare shield are drawn side by side to the same lug; one ground wire represents both.Wireblack
5Toggle frame lugGround (Volume casing)The source shows a ground symbol.To a pot casing
6Volume right lugVolume casingShort link.To a pot casingblack
7.022µf capacitorTone casingTo a pot casing
8Tone casingGround (Volume casing)The source shows a ground symbol.To a pot casing
9Jack sleeveGround (Volume casing)The source shows a ground symbol.Wire
10Ground Wire from BridgeVolume casingThe source also shows a ground symbol at this solder spot.To a pot casing
11Neck Pickup (P90) bare shieldToggle frame lugShield or groundbare
12Bridge redToggle lower outer lugWirered
13Neck whiteToggle upper outer lugWirewhite
14Toggle middle lugVolume left lugWire
15Bridge blackPush/pull left middle lugWireblack
16Bridge whitePush/pull left middle lugShares the lug with the bridge black.Wirewhite
17Volume middle lugJack tipWire
18Volume left lugTone left lugWire
19Tone middle lug.022µf capacitorWire

What each position does

SettingThe sourceEngine result
Neck, knob down: P90DOWN: Humbucker.Neck Pickup (P90).
Both, knob down: P90 + full humbuckerDOWN: Humbucker.Neck Pickup (P90) and Bridge Pickup (both coils) in parallel.
Bridge, knob down: full humbuckerDOWN: Humbucker.Bridge Pickup (both coils).
Neck, knob pulled: P90UP: Split (Slug Coil). Neck is unchanged.Neck Pickup (P90).
Both, knob pulled: P90 + split bridgeUP: Split (Slug Coil).Neck Pickup (P90) and Bridge Pickup (split to one coil) in parallel.
Bridge, knob pulled: slug coilUP: Split (Slug Coil).Bridge Pickup (split to one coil).

Checked with the Tinkercaster wiring engine against the switching the source describes.

  • The P90 is simulated from its catalog leads (white hot, black ground, bare shield); hum cancelling and phase follow the pickups' lead colours and coil polarity as Tonerider publishes them; nothing here is measured.
  • Hum cancelling and phase follow the pickups' lead colours and coil polarity as Tonerider publishes them; nothing here is measured.
  • The source says the split keeps the slug coil; the catalog pickups do not know which physical coil is the slug, so it only shows that one coil remains.
  • The source does not label the toggle positions; they follow the usual neck, both, bridge order.
  • Pickup resistance is not specified, so no numeric meter readings are given.

Before you solder

Ticks are kept in this browser only, as a reminder. They are not a check of your joints. New to soldering? Read the soldering cheat sheet .

Check before plugging in

  • Knob down: in each toggle position the meter across the jack reads the P90, both pickups in parallel, or the full humbucker.
  • Knob up: the bridge reading drops to roughly one coil's resistance; the neck alone is unchanged.
  • With the volume at zero, tip and sleeve should read as a short in every position.

Measure across the output jack with a multimeter on its resistance range. No exact readings are given where the source does not specify the pickups.