Parts and values
| In the drawing | Value | Part |
|---|---|---|
| Neck Pickup (Rebel 90) | — | Tonerider Rebel 90 |
| Bridge Pickup | — | Tonerider Alnico 2 Classic |
| 3-Way Toggle | — | Switchcraft 3-Way Toggle |
| Volume 500kA (push-pull) | 500k | 500k Push-Pull DPDT |
| Tone 500kA | 500k | CTS 500k Audio Pot |
| .022µf | 22nF | Orange Drop .022µF |
| Output Jack | — | Switchcraft #11 |
| Ground Wire from Bridge | — | Bridge ground wire |
Every pickup is the maker's own. “As specified” means the sheet names that part. “Example part” means the sheet names no model: the pickup shown is one of the maker's with the same leads, and any pot, cap or switch with the same value and lugs will do. “Generic” is a plain part such as a ground wire. “Not on the sheet; stand-in” means the sheet prints no value for that part, so the value shown is the usual one, not the maker's.
Connections
In soldering order: grounds first, then the switch, the pickups and the signal path.
| # | From | To | How |
|---|---|---|---|
| 1 | Push/pull left lug nearest the pot | Volume casing | To a pot casing |
| 2 | Bridge green | Volume casing | To a pot casing |
| 3 | Bridge bare shield | Volume casing | Shield or ground |
| 4 | Neck black and bare shield | Toggle frame lug | Wire |
| 5 | Toggle frame lug | Ground (Volume casing) | To a pot casing |
| 6 | Volume right lug | Volume casing | To a pot casing |
| 7 | .022µf capacitor | Tone casing | To a pot casing |
| 8 | Tone casing | Ground (Volume casing) | To a pot casing |
| 9 | Jack sleeve | Ground (Volume casing) | Wire |
| 10 | Ground Wire from Bridge | Volume casing | To a pot casing |
| 11 | Neck Pickup (Rebel 90) bare shield | Toggle frame lug | Shield or ground |
| 12 | Bridge red | Toggle lower outer lug | Wire |
| 13 | Neck white | Toggle upper outer lug | Wire |
| 14 | Toggle middle lug | Volume left lug | Wire |
| 15 | Bridge black | Push/pull left middle lug | Wire |
| 16 | Bridge white | Push/pull left middle lug | Wire |
| 17 | Volume middle lug | Jack tip | Wire |
| 18 | Volume left lug | Tone left lug | Wire |
| 19 | Tone middle lug | .022µf capacitor | Wire |
What each position does
| Setting | The source | Engine result |
|---|---|---|
| Neck, knob down: Rebel 90 | DOWN: Humbucker. | Neck Pickup (Rebel 90). |
| Both, knob down: Rebel 90 + full humbucker | DOWN: Humbucker. | Neck Pickup (Rebel 90) and Bridge Pickup (both coils) in parallel. |
| Bridge, knob down: full humbucker | DOWN: Humbucker. | Bridge Pickup (both coils). |
| Neck, knob pulled: Rebel 90 | UP: Split (Slug Coil). Neck is unchanged. | Neck Pickup (Rebel 90). |
| Both, knob pulled: Rebel 90 + split bridge | UP: Split (Slug Coil). | Neck Pickup (Rebel 90) and Bridge Pickup (split to one coil) in parallel. |
| Bridge, knob pulled: slug coil | UP: Split (Slug Coil). | Bridge Pickup (split to one coil). |
Checked with the Tinkercaster wiring engine against the switching the source describes.
- The Rebel 90 is simulated from its catalog leads (white hot, black ground, bare shield); hum cancelling and phase follow the pickups' lead colours and coil polarity as Tonerider publishes them; nothing here is measured.
- Hum cancelling and phase follow the pickups' lead colours and coil polarity as Tonerider publishes them; nothing here is measured.
- The source says the split keeps the slug coil; the catalog pickups do not know which physical coil is the slug, so it only shows that one coil remains.
- The source does not label the toggle positions; they follow the usual neck, both, bridge order.
- Pickup resistance is not specified, so no numeric meter readings are given.
Before you solder
Ticks are kept in this browser only, as a reminder. They are not a check of your joints. New to soldering? Read the soldering cheat sheet .
Check before plugging in
- Knob down: in each toggle position the meter across the jack reads the Rebel 90, both pickups in parallel, or the full humbucker.
- Knob up: the bridge reading drops to roughly one coil's resistance; the neck alone is unchanged.
- With the volume at zero, tip and sleeve should read as a short in every position.
Measure across the output jack with a multimeter on its resistance range. No exact readings are given where the source does not specify the pickups.