Skip to content
Tinkercaster

Tonerider wiring

Two Rebel 90 pickups with a three-way toggle, one volume and one tone

Two Rebel 90 · Three-way toggle · One volume · One tone

Tonerider's two Rebel 90 harness: neck and bridge Rebel 90 pickups on a three-way toggle, then a 500kA volume and a 500kA tone with a .022 µF capacitor.

Viewed from the back of the controls, as you solder them.

Two Rebel 90 pickups with a three-way toggle, one volume and one toneTwo Rebel 90 pickups with a three-way toggle, one volume and one tone: Two Rebel 90 · Three-way toggle · One volume · One tone. Original Tinkercaster drawing with labelled terminals.Neck Pickup (Rebel 90)Bridge Pickup (Rebel 90)500k500k22nFwhiteblackbarewhiteblackbareT1T2T3T4lug1lug2lug3lug1lug2lug3tipsleeveabgroundNeck Pickup (Rebel 90)Bridge Pickup (Rebel 90)3-Way ToggleVolume 500kATone 500kAOutput Jack.022µfGround Wire from Bridge

Open the interactive diagram to zoom, move components and try the switches.

Parts and values

In the drawingValuePart
Neck Pickup (Rebel 90)—Tonerider Rebel 90As specified
Bridge Pickup (Rebel 90)—Tonerider Rebel 90As specified
3-Way Toggle—Switchcraft 3-Way ToggleExample part
Volume 500kA500kCTS 500k Audio PotExample part
Tone 500kA500kCTS 500k Audio PotExample part
Output Jack—Switchcraft #11Example part
.022µfSource: .022µf capacitor (drawn orange)22nFOrange Drop .022µFExample part
Ground Wire from Bridge—Bridge ground wireGeneric

Every pickup is the maker's own. “As specified” means the sheet names that part. “Example part” means the sheet names no model: the pickup shown is one of the maker's with the same leads, and any pot, cap or switch with the same value and lugs will do. “Generic” is a plain part such as a ground wire. “Not on the sheet; stand-in” means the sheet prints no value for that part, so the value shown is the usual one, not the maker's.

Connections

In soldering order: grounds first, then the switch, the pickups and the signal path.

#FromToHow
1Neck black and bare shieldToggle frame lugThe black lead and the bare shield are drawn side by side to the same lug; one ground wire represents both.Wireblack
2Bridge black and bare shieldToggle frame lugThe black lead and the bare shield are drawn side by side to the same lug; one ground wire represents both.Wireblack
3Toggle frame lugGround (Volume casing)The source shows a ground symbol.To a pot casing
4Volume right lugVolume casingShort link.To a pot casingblack
5.022µf capacitorTone casingTo a pot casing
6Tone casingGround (Volume casing)The source shows a ground symbol.To a pot casing
7Jack sleeveGround (Volume casing)The source shows a ground symbol.Wire
8Ground Wire from BridgeVolume casingTo a pot casing
9Neck Pickup (Rebel 90) bare shieldToggle frame lugShield or groundbare
10Bridge Pickup (Rebel 90) bare shieldToggle frame lugShield or groundbare
11Neck whiteToggle upper outer lugWirewhite
12Bridge whiteToggle lower outer lugWirewhite
13Toggle middle lugVolume left lugWire
14Volume middle lugJack tipWire
15Volume left lugTone left lugWire
16Tone middle lug.022µf capacitorWire

What each position does

SettingThe sourceEngine result
Neck: Rebel 90The neck white lead is on the toggle's upper outer lug.Neck Pickup (Rebel 90).
Middle: both pickupsBoth outer toggle lugs join the middle lug.Neck Pickup (Rebel 90) and Bridge Pickup (Rebel 90) in parallel.
Bridge: Rebel 90The bridge white lead is on the toggle's lower outer lug.Bridge Pickup (Rebel 90).

Checked with the Tinkercaster wiring engine against the switching the source describes.

  • Each Rebel 90 is simulated from its catalog leads (white hot, black ground, bare shield); hum cancelling and phase follow the pickups' lead colours and coil polarity as Tonerider publishes them; nothing here is measured.
  • The source does not label the toggle positions; they follow the usual neck, both, bridge order.
  • Pickup resistance is not specified, so no numeric meter readings are given.

Before you solder

Ticks are kept in this browser only, as a reminder. They are not a check of your joints. New to soldering? Read the soldering cheat sheet .

Check before plugging in

  • In each toggle position the meter across the jack reads the neck Rebel 90, both pickups in parallel, or the bridge Rebel 90.
  • With the volume at zero, tip and sleeve should read as a short in every position.

Measure across the output jack with a multimeter on its resistance range. No exact readings are given where the source does not specify the pickups.