Skip to content
Tinkercaster

DiMarzio wiring

Humbucker bridge and rail-style neck with a three-way blade switch

Humbucker bridge, rail-style neck · Three-way blade · One volume · One tone

DiMarzio's HS layout on a three-way Tele-style blade switch: a four-conductor rail-style neck pickup and a bridge humbucker, three short jumpers on the switch, then 500K custom-taper volume and tone pots with a .022 µF capacitor.

Viewed from the back of the controls, as you solder them.

Humbucker bridge and rail-style neck with a three-way blade switchHumbucker bridge and rail-style neck with a three-way blade switch: Humbucker bridge, rail-style neck · Three-way blade · One volume · One tone. Original Tinkercaster drawing with labelled terminals.Rail-style neck pickupBridge pickup500k500k22nFredgreenblackwhitebareredgreenblackwhitebareT1T2T3T4T5T6T7T8lug1lug2lug3lug1lug2lug3tipsleeveabgroundRail-style neck pickupBridge pickup3-way blade switchVolume 500K custom taperTone 500K custom taperOutput jack.022µFBridge ground

Open the interactive diagram to zoom, move components and try the switches.

Parts and values

In the drawingValuePart
Rail-style neck pickupSource: Neck pickup, rail-style (BARE, GREEN, RED, BLACK, WHITE)—DiMarzio Fast Track 1 DP181Example partSame wiring for DiMarzio Fast Track 2 DP182, DiMarzio The Cruiser Neck DP186, DiMarzio The Chopper DP184, DiMarzio Air Norton S DP180, DiMarzio BC-1 DP225
Bridge pickupSource: Bridge pickup (BARE, GREEN, RED, BLACK, WHITE)—Super Distortion DP100Example partSame wiring for DiMarzio Dual Sound DP101, DiMarzio Super 2 DP104, DiMarzio DLX Plus Bridge DP154, DiMarzio Norton DP160, DiMarzio Steve's Special DP161, DiMarzio D Sonic DP207
3-way blade switchSource: Three-way switch for Tele (EP1105)—CRL 3-Way BladeExample part
Volume 500K custom taperSource: Volume 500K custom taper pot (EP1201)500kCTS 500k Audio PotExample part
Tone 500K custom taperSource: Tone 500K custom taper pot (EP1201)500kCTS 500k Audio PotExample part
Output jackSource: Switchcraft output jack, 2-conductor (EP1301)—Switchcraft #11Example part
.022µFSource: .022µF capacitor (EP1022)22nFOrange Drop .022µFExample part
Bridge groundSource: TO BRIDGE GROUND—Bridge ground wireGeneric

Every pickup is the maker's own. “As specified” means the sheet names that part. “Example part” means the sheet names no model: the pickup shown is one of the maker's with the same leads, and any pot, cap or switch with the same value and lugs will do. “Generic” is a plain part such as a ground wire. “Not on the sheet; stand-in” means the sheet prints no value for that part, so the value shown is the usual one, not the maker's.

Understand this wiring

  • DiMarzio humbucker wire colors

    Red is hot, black and white join each other, green and bare go to ground. See why, and what changes when you reverse the phase.

All DiMarzio wiring guides →

Connections

In soldering order: grounds first, then the switch, the pickups and the signal path.

#FromToHow
1Neck GREENVolume casingTo a pot casinggreen
2Neck BAREVolume casingShield or groundbare
3Bridge GREENVolume casingTo a pot casinggreen
4Bridge BAREVolume casingShield or groundbare
5Volume top lugVolume casingTo a pot casingblack
6Volume top lugTone casingThe tone casing also carries a ground symbol.To a pot casingblack
7.022µF capacitorTone casingTo a pot casing
8Tone casingJack sleeveWireblack
9TO BRIDGE GROUNDJack sleeveThe jack sleeve also carries a ground symbol.Shield or groundblack
10Neck REDSwitch upper-left tagWirered
11Bridge REDSwitch lower-right tagWirered
12Switch lower-left tagSwitch second lower tagShort jumper.Jumper
13Switch second lower tagSwitch third upper tagShort jumper between the rows.Jumper
14Switch third upper tagSwitch upper-right tagShort jumper to the output tag.Jumper
15Switch upper-right tagVolume bottom lug (input)Wire
16Neck BLACKNeck WHITEJoined at one end dot.Joined and insulatedblack
17Bridge BLACKBridge WHITEJoined at one end dot.Joined and insulatedblack
18Volume middle lugJack tipWire
19Volume bottom lugTone middle lug (wiper)Wire
20Tone bottom lug.022µF capacitorWire

What each position does

SettingThe sourceEngine result
NeckPosition 1 = neck.Rail-style neck pickup (both coils).
Neck and bridgePosition 2 = neck & bridge.Rail-style neck pickup (both coils) and Bridge pickup (both coils) in parallel.
BridgePosition 3 = bridge.Bridge pickup (both coils).

Checked with the Tinkercaster wiring engine against the switching the source describes.

  • The source's 500K custom taper is not reproduced: both pots are simulated with the stand-in's audio taper, so settings between the knob ends are approximate.
  • Hum cancelling and phase follow the pickups' lead colours and coil polarity as DiMarzio publishes them; nothing here is measured.
  • Pickup resistance is not specified, so no numeric meter readings are given.

Before you solder

Ticks are kept in this browser only, as a reminder. They are not a check of your joints. New to soldering? Read the soldering cheat sheet .

Check before plugging in

  • In each switch position, the meter across the jack should read the selected pickup, or both in parallel in the middle.
  • The four jumpered switch tags and the volume input lug should always read as one connection.
  • Each joined black–white pair should read about one coil's resistance to ground, roughly half the pickup's total (a few kΩ): not open, and not zero.

Measure across the output jack with a multimeter on its resistance range. No exact readings are given where the source does not specify the pickups.