Skip to content
Tinkercaster

Seymour Duncan wiring

SCH, Strat Stack Plus and SCH on a 5-way blade with one volume

Single-coil-sized humbucker · Strat Stack Plus · Single-coil-sized humbucker · 5-way blade · One volume

Seymour Duncan sheet: single-coil-sized humbuckers in the neck and bridge (red and white taped off, full humbucker) with a Strat Stack Plus in the middle (red taped off), on a standard 5-way blade and one 250k master volume.

Viewed from the back of the controls, as you solder them.

SCH, Strat Stack Plus and SCH on a 5-way blade with one volumeSCH, Strat Stack Plus and SCH on a 5-way blade with one volume: Single-coil-sized humbucker · Strat Stack Plus · Single-coil-sized humbucker · 5-way blade · One volume. Original Tinkercaster drawing with labelled terminals.Neck SCHMiddle Strat Stack PlusBridge SCH250kblackgreenwhiteredbarewhiteredblackbareblackgreenwhiteredbareT1T2T3T4T5T6T7T8lug1lug2lug3tipsleevegroundNeck SCHMiddle Strat Stack PlusBridge SCH5-way bladeMaster volume 250kOutput JackGround wire to bridge

Open the interactive diagram to zoom, move components and try the switches.

Parts and values

In the drawingValuePart
Neck SCH—Little '59 SL59-1 Neck (Strat-size)Example partSame wiring for JB Jr. SJBJ-1 Bridge (Strat-size), Hot Rails SHR-1 Bridge (Strat-size)
Middle Strat Stack Plus—Strat Stack PlusExample partSame wiring for Seymour Duncan STK-S4 Stack Plus
Bridge SCH—Little '59 SL59-1 Bridge (Strat-size)Example partSame wiring for JB Jr. SJBJ-1 Bridge (Strat-size), Hot Rails SHR-1 Bridge (Strat-size)
5-way blade—Oak Grigsby 5-WayExample part
Master volume 250k250kCTS 250k Audio PotExample part
Output Jack—Switchcraft #11Example part
Ground wire to bridge—Bridge ground wireGeneric

Every pickup is the maker's own. “As specified” means the sheet names that part. “Example part” means the sheet names no model: the pickup shown is one of the maker's with the same leads, and any pot, cap or switch with the same value and lugs will do. “Generic” is a plain part such as a ground wire. “Not on the sheet; stand-in” means the sheet prints no value for that part, so the value shown is the usual one, not the maker's.

Understand this wiring

All Seymour Duncan wiring guides →

Connections

In soldering order: grounds first, then the switch, the pickups and the signal path.

#FromToHow
1Neck greenVolume casing (upper Solder spot)To a pot casinggreen
2Neck bareVolume casing (upper Solder spot)To a pot casingbare
3Bridge greenVolume casing (upper Solder spot)To a pot casinggreen
4Bridge bareVolume casing (upper Solder spot)To a pot casingbare
5Middle blackVolume casing (upper Solder spot)To a pot casingblack
6Middle bare (drain)Volume casing (upper Solder spot)Drawn tan.To a pot casingbare
7Ground wire to bridgeVolume casing (upper Solder spot)To a pot casingblack
8Volume third lugVolume casing (lower Solder spot)Lug bent onto the casing.To a pot casingground
9Volume casing (upper Solder spot)Jack sleeveTo a pot casingblack
10Bridge blackBlade lug 1 (far end from the common)Labelled 'bridge white' on the sheet but drawn black and traced to the bridge cable's black lead; see notes.Wireblack
11Middle whiteBlade lug 2Printed 'middle white'.Wirewhite
12Neck blackBlade lug 3Printed 'neck black'.Wireblack
13Blade common (lug 4)Other row's commonRuns across the switch.Wireblack
14Other row's commonVolume first lugWireblack
15Neck whiteNeck redPrinted 'Red & white wires get taped off' (joined in one taped end).Wirered
16Bridge whiteBridge redPrinted 'Red & white wires get taped off' (joined in one taped end).Wirered
17Volume middle lugJack tipHops over the sleeve wire.Wireblack

What each position does

SettingThe sourceEngine result
BridgeThe sheet prints no position legend; this state follows the drawn leads on the standard 5-way blade.Bridge SCH (both coils).
Bridge + middleThe sheet prints no position legend; this state follows the drawn leads on the standard 5-way blade.Middle Strat Stack Plus (both coils) and Bridge SCH (both coils) in parallel.
MiddleThe sheet prints no position legend; this state follows the drawn leads on the standard 5-way blade.Middle Strat Stack Plus (both coils).
Middle + neckThe sheet prints no position legend; this state follows the drawn leads on the standard 5-way blade.Neck SCH (both coils) and Middle Strat Stack Plus (both coils) in parallel.
NeckThe sheet prints no position legend; this state follows the drawn leads on the standard 5-way blade.Neck SCH (both coils).

Checked with the Tinkercaster wiring engine against the switching the source describes.

  • The small component printed on the Strat Stack Plus board is not modelled; the sheet prints no value for it and the red tap is taped off.
  • Pickup resistance is not specified, so no numeric meter readings are given.

Before you solder

Ticks are kept in this browser only, as a reminder. They are not a check of your joints. New to soldering? Read the soldering cheat sheet .

Check before plugging in

  • In each position the meter across the jack should read the selected pickup(s), each whole.
  • With the volume at zero, tip and sleeve should read as a short.

Measure across the output jack with a multimeter on its resistance range. No exact readings are given where the source does not specify the pickups.