Parts and values
| In the drawing | Value | Part |
|---|---|---|
| Neck pickup | — | Vintage Tele Rhythm STR-1 |
| Bridge pickup | — | Seymour Duncan Hot Rails for Tele |
| 3-Way Switch | — | CRL 3-Way Blade |
| Neck Volume 250k | 250k | CTS 250k Audio Pot |
| Bridge Volume 250k | 250k | CTS 250k Audio Pot |
| Output Jack | — | Switchcraft #11 |
| Bridge Ground | — | Bridge ground wire |
Every pickup is the maker's own. “As specified” means the sheet names that part. “Example part” means the sheet names no model: the pickup shown is one of the maker's with the same leads, and any pot, cap or switch with the same value and lugs will do. “Generic” is a plain part such as a ground wire. “Not on the sheet; stand-in” means the sheet prints no value for that part, so the value shown is the usual one, not the maker's.
Understand this wiring
- Seymour Duncan humbucker wire colors
See the pickup, recognise its two halves, and learn where each coloured wire goes.
Connections
In soldering order: grounds first, then the switch, the pickups and the signal path.
| # | From | To | How |
|---|---|---|---|
| 1 | Neck single coil black | Neck volume casing | To a pot casing |
| 2 | Bridge humbucker green | Bridge volume casing | To a pot casing |
| 3 | Neck volume right lug | Neck volume casing | To a pot casing |
| 4 | Bridge volume right lug | Bridge volume casing | To a pot casing |
| 5 | Neck volume casing | Bridge volume casing | To a pot casing |
| 6 | Bridge volume casing | Jack sleeve | Wire |
| 7 | Bridge ground wire | Neck volume casing | Shield or ground |
| 8 | Bridge humbucker bare | Bridge volume casing | Shield or ground |
| 9 | Neck volume middle lug | Switch top-right lug (common) | Wire |
| 10 | Bridge volume middle lug | Switch bottom-left lug (common) | Wire |
| 11 | Switch top-left lug | Switch second left lug | Jumper |
| 12 | Switch second left lug | Switch third right lug | Jumper |
| 13 | Switch third right lug | Switch bottom-right lug | Jumper |
| 14 | Switch bottom-right lug | Jack tip | Wire |
| 15 | Neck single coil white | Neck volume left lug (input) | Wire |
| 16 | Bridge humbucker black (hot) | Bridge volume left lug (input) | Wire |
| 17 | Bridge humbucker red | Bridge humbucker white | Joined and insulated |
What each position does
| Setting | The source | Engine result |
|---|---|---|
| Neck | — | Neck pickup. |
| Neck + bridge | — | Neck pickup and Bridge pickup (both coils) in parallel. |
| Bridge | — | Bridge pickup (both coils). |
Checked with the Tinkercaster wiring engine against the switching the source describes.
- Hum cancelling and phase follow the pickups' lead colours and coil polarity as Seymour Duncan publishes them; nothing here is measured.
- Pickup resistance is not specified, so no numeric meter readings are given.
Before you solder
Ticks are kept in this browser only, as a reminder. They are not a check of your joints. New to soldering? Read the soldering cheat sheet .
Check before plugging in
- In each blade position, the meter across the jack should read the selected pickup, or both in parallel in the middle.
- With the selected pickup's volume at zero, tip and sleeve should read as a short.
- The taped red and white joint should read about one coil's resistance to ground and to the hot lead (roughly half the pickup's total), and should touch nothing else.
Measure across the output jack with a multimeter on its resistance range. No exact readings are given where the source does not specify the pickups.