Skip to content
Tinkercaster

Seymour Duncan wiring

Three single-coil-sized humbuckers on a super 5-way blade with one volume

Three single-coil-sized humbuckers · 4-pole super 5-way · One volume

Seymour Duncan sheet: three single-coil-sized humbuckers (SCH) on a 4-pole 5-way super switch and one 250k volume. Positions 1, 3 and 5 use the bridge, middle and neck as full humbuckers; positions 2 and 4 split both selected pickups for hum-cancelling single-coil pairs.

Viewed from the back of the controls, as you solder them.

Three single-coil-sized humbuckers on a super 5-way blade with one volumeThree single-coil-sized humbuckers on a super 5-way blade with one volume: Three single-coil-sized humbuckers · 4-pole super 5-way · One volume. Original Tinkercaster drawing with labelled terminals.Neck SCHMiddle SCHBridge SCH250kblackgreenwhiteredbareblackgreenwhiteredbareblackgreenwhiteredbareT1T2T3T4T5T6T7T8T9T10T11T12T13T14T15T16T17T18T19T20T21T22T23T24lug1lug2lug3tipsleevegroundNeck SCHMiddle SCHBridge SCH5-way super-switchVolume 250kOutput JackGround wire to bridge

Open the interactive diagram to zoom, move components and try the switches.

Parts and values

In the drawingValuePart
Neck SCH—Little '59 SL59-1 Neck (Strat-size)Example partSame wiring for Hot Rails SHR-1 Bridge (Strat-size), JB Jr. SJBJ-1 Bridge (Strat-size)
Middle SCH—Little '59 SL59-1 Neck (Strat-size)Example partSame wiring for Hot Rails SHR-1 Bridge (Strat-size), JB Jr. SJBJ-1 Bridge (Strat-size)
Bridge SCH—JB Jr. SJBJ-1 Bridge (Strat-size)Example partSame wiring for Little '59 SL59-1 Bridge (Strat-size), Hot Rails SHR-1 Bridge (Strat-size)
5-way super-switch—Oak Grigsby 4-Pole 5-Way Super SwitchExample part
Volume 250k250kCTS 250k Audio PotExample part
Output Jack—Switchcraft #11Example part
Ground wire to bridge—Bridge ground wireGeneric

Every pickup is the maker's own. “As specified” means the sheet names that part. “Example part” means the sheet names no model: the pickup shown is one of the maker's with the same leads, and any pot, cap or switch with the same value and lugs will do. “Generic” is a plain part such as a ground wire. “Not on the sheet; stand-in” means the sheet prints no value for that part, so the value shown is the usual one, not the maker's.

Understand this wiring

All Seymour Duncan wiring guides →

Connections

In soldering order: grounds first, then the switch, the pickups and the signal path.

#FromToHow
1Middle greenLeft wafer lug 8Printed 'middle green & black'.Wiregreen
2Right wafer lug 12 (bottom)Volume casing (upper Solder spot)To a pot casingblack
3Neck greenVolume casing (upper Solder spot)To a pot casinggreen
4Neck bareVolume casing (upper Solder spot)To a pot casingbare
5Bridge greenVolume casing (upper Solder spot)To a pot casinggreen
6Bridge bareVolume casing (upper Solder spot)To a pot casingbare
7Middle whiteVolume casing (upper Solder spot)Printed 'WHITE & bare from middle pickup'.To a pot casingwhite
8Middle bareVolume casing (upper Solder spot)To a pot casingbare
9Ground wire to bridgeVolume casing (upper Solder spot)To a pot casingblack
10Volume third lugVolume casing (lower Solder spot)Lug bent onto the casing.To a pot casingground
11Volume casing (lower Solder spot)Jack sleeveTo a pot casingblack
12Bridge blackRight wafer lug 2Wireblack
13Right wafer lug 2Right wafer lug 3Short jumper.Wireblack
14Neck blackRight wafer lug 5Wireblack
15Right wafer lug 5Right wafer lug 6Short jumper.Wireblack
16Middle redLeft wafer lug 3Runs over the top of the switch.Wirered
17Left wafer lug 3Left wafer lug 4Short jumper.Wireblack
18Left wafer lug 4Left wafer lug 5Short jumper.Wireblack
19Middle blackLeft wafer lug 8Printed 'middle green & black'.Wireblack
20Left wafer lug 8Left wafer lug 10Jumper.Wireblack
21Bridge whiteRight wafer lug 8Printed 'bridge red & white'.Wirewhite
22Bridge redRight wafer lug 8Printed 'bridge red & white'.Wirered
23Neck whiteRight wafer lug 10Printed 'neck red & white'.Wirewhite
24Neck redRight wafer lug 10Printed 'neck red & white'.Wirered
25Left wafer lug 1 (top)Right wafer lug 1 (top)Arcs over the top of the switch.Wireblack
26Left wafer lug 1 (top)Volume first lugLoops round the far side of the switch.Wireblack
27Left wafer lug 12 (bottom)Right wafer lug 12 (bottom)Loops under the switch.Wireblack
28Volume middle lugJack tipWireblack

What each position does

SettingThe sourceEngine result
Bridge full humbucker—Bridge SCH (both coils).
Bridge & middle (both split, hum-canceling)—Middle SCH (split to one coil) and Bridge SCH (split to one coil) in parallel.
Middle full humbucker—Middle SCH (both coils).
Middle & neck (both split, hum-canceling)—Neck SCH (split to one coil) and Middle SCH (split to one coil) in parallel.
Neck full humbucker—Neck SCH (both coils).

Checked with the Tinkercaster wiring engine against the switching the source describes.

  • The sheet wires the middle pickup reversed (green and black are the series link on the switch, white is grounded); the editor checks recognise this reversed-lead wiring (hot and return leads joined as the link). The engine's per-position pickup selection and coil modes match all five legend positions.
  • Hum cancelling in the split positions depends on the real pickups' coil polarity, which this reference does not measure.
  • Pickup resistance is not specified, so no numeric meter readings are given.

Before you solder

Ticks are kept in this browser only, as a reminder. They are not a check of your joints. New to soldering? Read the soldering cheat sheet .

Check before plugging in

  • In positions 1, 3 and 5 the meter across the jack should read one whole pickup; in positions 2 and 4 two split pickups in parallel.
  • With the volume at zero, tip and sleeve should read as a short.

Measure across the output jack with a multimeter on its resistance range. No exact readings are given where the source does not specify the pickups.