Skip to content
Tinkercaster

Seymour Duncan wiring

Three single-coil-sized humbuckers on a super 5-way blade with volume and tone

Three single-coil-sized humbuckers · 4-pole super 5-way · One volume · One tone

Seymour Duncan sheet: three single-coil-sized humbuckers (SCH) on a 4-pole 5-way super switch with one 250k volume, one 250k tone and a .047 cap. Positions 1, 3 and 5 use the bridge, middle and neck as full humbuckers; positions 2 and 4 split both selected pickups for hum-cancelling single-coil pairs.

Viewed from the back of the controls, as you solder them.

Three single-coil-sized humbuckers on a super 5-way blade with volume and toneThree single-coil-sized humbuckers on a super 5-way blade with volume and tone: Three single-coil-sized humbuckers · 4-pole super 5-way · One volume · One tone. Original Tinkercaster drawing with labelled terminals.Neck SCHMiddle SCHBridge SCH250k250k47nFblackgreenwhiteredbareblackgreenwhiteredbareblackgreenwhiteredbareT1T2T3T4T5T6T7T8T9T10T11T12T13T14T15T16T17T18T19T20T21T22T23T24lug1lug2lug3tipsleevegroundlug1lug2lug3abNeck SCHMiddle SCHBridge SCH5-way super-switchVolume 250kOutput JackGround wire to bridgeTone 250k.047 tone cap · 47nF

Open the interactive diagram to zoom, move components and try the switches.

Parts and values

In the drawingValuePart
Neck SCH—Little '59 SL59-1 Neck (Strat-size)Example partSame wiring for Hot Rails SHR-1 Bridge (Strat-size), JB Jr. SJBJ-1 Bridge (Strat-size)
Middle SCH—Little '59 SL59-1 Neck (Strat-size)Example partSame wiring for Hot Rails SHR-1 Bridge (Strat-size), JB Jr. SJBJ-1 Bridge (Strat-size)
Bridge SCH—JB Jr. SJBJ-1 Bridge (Strat-size)Example partSame wiring for Little '59 SL59-1 Bridge (Strat-size), Hot Rails SHR-1 Bridge (Strat-size)
5-way super-switch—Oak Grigsby 4-Pole 5-Way Super SwitchExample part
Volume 250k250kCTS 250k Audio PotExample part
Output Jack—Switchcraft #11Example part
Ground wire to bridge—Bridge ground wireGeneric
Tone 250k250kCTS 250k Audio PotExample part
.047 tone capSource: .047 cap47nFOrange Drop .047µFExample part

Every pickup is the maker's own. “As specified” means the sheet names that part. “Example part” means the sheet names no model: the pickup shown is one of the maker's with the same leads, and any pot, cap or switch with the same value and lugs will do. “Generic” is a plain part such as a ground wire. “Not on the sheet; stand-in” means the sheet prints no value for that part, so the value shown is the usual one, not the maker's.

Understand this wiring

All Seymour Duncan wiring guides →

Connections

In soldering order: grounds first, then the switch, the pickups and the signal path.

#FromToHow
1Middle greenLeft wafer lug 8Printed 'middle green & black'.Wiregreen
2Right wafer lug 12 (bottom)Volume casing (upper Solder spot)To a pot casingblack
3Neck greenVolume casing (upper Solder spot)To a pot casinggreen
4Neck bareVolume casing (upper Solder spot)To a pot casingbare
5Bridge greenVolume casing (upper Solder spot)To a pot casinggreen
6Bridge bareVolume casing (upper Solder spot)To a pot casingbare
7Middle whiteVolume casing (upper Solder spot)Printed 'WHITE & bare from middle pickup'.To a pot casingwhite
8Middle bareVolume casing (upper Solder spot)To a pot casingbare
9Ground wire to bridgeVolume casing (upper Solder spot)To a pot casingblack
10Volume third lugVolume casing (lower Solder spot)Lug bent onto the casing.To a pot casingground
11Volume casing (lower Solder spot)Jack sleeveTo a pot casingblack
12.047 capTone casing (Solder spot)To a pot casing
13Tone casing (Solder spot)Volume casing (lower Solder spot)To a pot casingblack
14Bridge blackRight wafer lug 2Wireblack
15Right wafer lug 2Right wafer lug 3Short jumper.Wireblack
16Neck blackRight wafer lug 5Wireblack
17Right wafer lug 5Right wafer lug 6Short jumper.Wireblack
18Middle redLeft wafer lug 3Runs over the top of the switch.Wirered
19Left wafer lug 3Left wafer lug 4Short jumper.Wireblack
20Left wafer lug 4Left wafer lug 5Short jumper.Wireblack
21Middle blackLeft wafer lug 8Printed 'middle green & black'.Wireblack
22Left wafer lug 8Left wafer lug 10Jumper.Wireblack
23Bridge whiteRight wafer lug 8Printed 'bridge red & white'.Wirewhite
24Bridge redRight wafer lug 8Printed 'bridge red & white'.Wirered
25Neck whiteRight wafer lug 10Printed 'neck red & white'.Wirewhite
26Neck redRight wafer lug 10Printed 'neck red & white'.Wirered
27Left wafer lug 1 (top)Right wafer lug 1 (top)Arcs over the top of the switch.Wireblack
28Left wafer lug 1 (top)Volume first lugLoops round the far side of the switch.Wireblack
29Left wafer lug 12 (bottom)Right wafer lug 12 (bottom)Loops under the switch.Wireblack
30Volume middle lugJack tipWireblack
31Volume first lugTone outer lug nearest the volumeWireblack
32Tone middle lug.047 capWire

What each position does

SettingThe sourceEngine result
Bridge full humbucker—Bridge SCH (both coils).
Bridge & middle (both split, hum-canceling)—Middle SCH (split to one coil) and Bridge SCH (split to one coil) in parallel.
Middle full humbucker—Middle SCH (both coils).
Middle & neck (both split, hum-canceling)—Neck SCH (split to one coil) and Middle SCH (split to one coil) in parallel.
Neck full humbucker—Neck SCH (both coils).

Checked with the Tinkercaster wiring engine against the switching the source describes.

  • The sheet wires the middle pickup reversed (green and black are the series link on the switch, white is grounded); the editor checks recognise this reversed-lead wiring (hot and return leads joined as the link). The engine's per-position pickup selection and coil modes match all five legend positions.
  • Hum cancelling in the split positions depends on the real pickups' coil polarity, which this reference does not measure.
  • Pickup resistance is not specified, so no numeric meter readings are given.

Before you solder

Ticks are kept in this browser only, as a reminder. They are not a check of your joints. New to soldering? Read the soldering cheat sheet .

Check before plugging in

  • In positions 1, 3 and 5 the meter across the jack should read one whole pickup; in positions 2 and 4 two split pickups in parallel.
  • With the volume at zero, tip and sleeve should read as a short.
  • Turning the tone down should load the selected pickups through the .047 µF capacitor.

Measure across the output jack with a multimeter on its resistance range. No exact readings are given where the source does not specify the pickups.