Skip to content
Tinkercaster

Seymour Duncan wiring

Three stacks on a super 5-way blade with volume and two tones

Three four-conductor stacked pickups · 4-pole super 5-way · One volume · Two tones, shared cap

Seymour Duncan three-stack sheet: four-conductor stacked pickups on a 4-pole 5-way super switch with one 250k volume and two 250k tones sharing one .047 cap. One tone hangs on the neck pickup's switch lead and the other on the middle pickup's, so each acts only when its pickup is selected.

Viewed from the back of the controls, as you solder them.

Three stacks on a super 5-way blade with volume and two tonesThree stacks on a super 5-way blade with volume and two tones: Three four-conductor stacked pickups · 4-pole super 5-way · One volume · Two tones, shared cap. Original Tinkercaster drawing with labelled terminals.Neck stackMiddle stackBridge stack250k250k250k47nFblackgreenwhiteredbareblackgreenwhiteredbareblackgreenwhiteredbareT1T2T3T4T5T6T7T8T9T10T11T12T13T14T15T16T17T18T19T20T21T22T23T24lug1lug2lug3tipsleevegroundlug1lug2lug3lug1lug2lug3abNeck stackMiddle stackBridge stack5-way super-switchVolume 250kOutput JackGround wire to bridgeTone 250k (upper, neck)Tone 250k (lower, middle).047 tone cap · 47nF

Open the interactive diagram to zoom, move components and try the switches.

Parts and values

In the drawingValuePart
Neck stack—Seymour Duncan STK-S10 YJM FuryExample partSame wiring for Seymour Duncan STK-P1 P-90 Stack
Middle stack—Seymour Duncan STK-S10 YJM FuryExample partSame wiring for Seymour Duncan STK-P1 P-90 Stack
Bridge stack—Seymour Duncan STK-S10 YJM FuryExample partSame wiring for Seymour Duncan STK-P1 P-90 Stack
5-way super-switch—Oak Grigsby 4-Pole 5-Way Super SwitchExample part
Volume 250k250kCTS 250k Audio PotExample part
Output Jack—Switchcraft #11Example part
Ground wire to bridge—Bridge ground wireGeneric
Tone 250k (upper, neck)Source: Tone 250k (upper, beside the volume)250kCTS 250k Audio PotExample part
Tone 250k (lower, middle)Source: Tone 250k (lower)250kCTS 250k Audio PotExample part
.047 tone capSource: .047 cap47nFOrange Drop .047µFExample part

Every pickup is the maker's own. “As specified” means the sheet names that part. “Example part” means the sheet names no model: the pickup shown is one of the maker's with the same leads, and any pot, cap or switch with the same value and lugs will do. “Generic” is a plain part such as a ground wire. “Not on the sheet; stand-in” means the sheet prints no value for that part, so the value shown is the usual one, not the maker's.

Understand this wiring

All Seymour Duncan wiring guides →

Connections

In soldering order: grounds first, then the switch, the pickups and the signal path.

#FromToHow
1Middle greenLeft wafer lug 8Printed 'middle green & black'.Wiregreen
2Right wafer lug 12 (bottom)Upper tone casing (Solder spot)To a pot casingblack
3Neck greenVolume casing (upper Solder spot)To a pot casinggreen
4Neck bareVolume casing (upper Solder spot)To a pot casingbare
5Bridge greenVolume casing (upper Solder spot)To a pot casinggreen
6Bridge bareVolume casing (upper Solder spot)To a pot casingbare
7Middle whiteVolume casing (upper Solder spot)Printed 'WHITE & bare from middle pickup'.To a pot casingwhite
8Middle bareVolume casing (upper Solder spot)To a pot casingbare
9Ground wire to bridgeVolume casing (upper Solder spot)To a pot casingblack
10Volume third lugVolume casing (lower Solder spot)Lug bent onto the casing.To a pot casingground
11Volume casing (lower Solder spot)Jack sleeveTo a pot casingblack
12.047 capUpper tone casing (Solder spot)To a pot casing
13Upper tone casing (Solder spot)Volume casing (lower Solder spot)To a pot casingblack
14Lower tone casing (Solder spot)Upper tone casing (Solder spot)To a pot casingblack
15Bridge blackRight wafer lug 3Wireblack
16Right wafer lug 3Right wafer lug 2Short jumper.Wireblack
17Neck blackRight wafer lug 5Wireblack
18Right wafer lug 5Right wafer lug 6Short jumper.Wireblack
19Middle redLeft wafer lug 3Runs over the top of the switch.Wirered
20Left wafer lug 3Left wafer lug 4Short jumper.Wireblack
21Left wafer lug 4Left wafer lug 5Short jumper.Wireblack
22Middle blackLeft wafer lug 8Printed 'middle green & black'.Wireblack
23Left wafer lug 8Left wafer lug 10Jumper.Wireblack
24Bridge whiteRight wafer lug 8Printed 'bridge red & white'.Wirewhite
25Bridge redRight wafer lug 8Printed 'bridge red & white'.Wirered
26Neck whiteRight wafer lug 10Printed 'neck red & white'.Wirewhite
27Neck redRight wafer lug 10Printed 'neck red & white'.Wirered
28Left wafer lug 1 (top)Right wafer lug 1 (top)Arcs over the top of the switch.Wireblack
29Right wafer lug 1 (top)Volume first lugRuns down past the pickup cables.Wireblack
30Left wafer lug 12 (bottom)Right wafer lug 12 (bottom)Loops under the switch.Wireblack
31Right wafer lug 6Upper tone middle lugCurves round the switch body (inner of the two leads).Wireblack
32Left wafer lug 5Lower tone first lugCurves round the switch body (outer of the two leads).Wireblack
33Volume middle lugJack tipWireblack
34Upper tone third lug.047 capWire
35Lower tone middle lugUpper tone third lugShares the upper tone's cap.Wireblack

What each position does

SettingThe sourceEngine result
Bridge full humbucker—Bridge stack (both coils).
Bridge & middle (both split, hum-canceling)—Middle stack (split to one coil) and Bridge stack (split to one coil) in parallel.
Middle full humbucker—Middle stack (both coils).
Middle & neck (both split, hum-canceling)—Neck stack (split to one coil) and Middle stack (split to one coil) in parallel.
Neck full humbucker—Neck stack (both coils).

Checked with the Tinkercaster wiring engine against the switching the source describes.

  • The sheet wires the middle pickup reversed (green and black are the series link on the switch, white is grounded); the editor checks recognise this reversed-lead wiring (hot and return leads joined as the link). The engine's per-position pickup selection and coil modes match all five legend positions.
  • Hum cancelling in the split positions depends on the real pickups' coil polarity, which this reference does not measure.
  • Pickup resistance is not specified, so no numeric meter readings are given.

Before you solder

Ticks are kept in this browser only, as a reminder. They are not a check of your joints. New to soldering? Read the soldering cheat sheet .

Check before plugging in

  • In positions 1, 3 and 5 the meter across the jack should read one whole pickup; in positions 2 and 4 two split pickups in parallel.
  • With the volume at zero, tip and sleeve should read as a short.
  • The upper tone should act whenever the neck pickup is selected (positions 4 and 5) and the lower tone whenever the middle pickup is selected (positions 2, 3 and 4).

Measure across the output jack with a multimeter on its resistance range. No exact readings are given where the source does not specify the pickups.