Skip to content
Tinkercaster

Seymour Duncan wiring

Three stacks on a super 5-way blade with one volume

Three four-conductor stacked pickups · 4-pole super 5-way · One volume

Seymour Duncan three-stack sheet: neck, middle and bridge four-conductor stacked pickups on a 4-pole 5-way super switch with one 250k volume. Positions 1, 3 and 5 use each stack whole; positions 2 and 4 split both selected stacks for hum-cancelling single-coil pairs.

Viewed from the back of the controls, as you solder them.

Three stacks on a super 5-way blade with one volumeThree stacks on a super 5-way blade with one volume: Three four-conductor stacked pickups · 4-pole super 5-way · One volume. Original Tinkercaster drawing with labelled terminals.Neck stackMiddle stackBridge stack250kblackgreenwhiteredbareblackgreenwhiteredbareblackgreenwhiteredbareT1T2T3T4T5T6T7T8T9T10T11T12T13T14T15T16T17T18T19T20T21T22T23T24lug1lug2lug3tipsleevegroundNeck stackMiddle stackBridge stack5-way super-switchVolume 250kOutput JackGround wire to bridge

Open the interactive diagram to zoom, move components and try the switches.

Parts and values

In the drawingValuePart
Neck stack—Seymour Duncan STK-S10 YJM FuryExample partSame wiring for Seymour Duncan STK-P1 P-90 Stack
Middle stack—Seymour Duncan STK-S10 YJM FuryExample partSame wiring for Seymour Duncan STK-P1 P-90 Stack
Bridge stack—Seymour Duncan STK-S10 YJM FuryExample partSame wiring for Seymour Duncan STK-P1 P-90 Stack
5-way super-switch—Oak Grigsby 4-Pole 5-Way Super SwitchExample part
Volume 250k250kCTS 250k Audio PotExample part
Output Jack—Switchcraft #11Example part
Ground wire to bridge—Bridge ground wireGeneric

Every pickup is the maker's own. “As specified” means the sheet names that part. “Example part” means the sheet names no model: the pickup shown is one of the maker's with the same leads, and any pot, cap or switch with the same value and lugs will do. “Generic” is a plain part such as a ground wire. “Not on the sheet; stand-in” means the sheet prints no value for that part, so the value shown is the usual one, not the maker's.

Understand this wiring

All Seymour Duncan wiring guides →

Connections

In soldering order: grounds first, then the switch, the pickups and the signal path.

#FromToHow
1Middle greenLeft wafer lug 8Printed 'middle green & black'.Wiregreen
2Right wafer lug 12 (bottom)Volume casing (lower Solder spot)To a pot casingblack
3Neck greenVolume casing (upper Solder spot)To a pot casinggreen
4Neck bareVolume casing (upper Solder spot)To a pot casingbare
5Bridge greenVolume casing (upper Solder spot)To a pot casinggreen
6Bridge bareVolume casing (upper Solder spot)To a pot casingbare
7Middle whiteVolume casing (upper Solder spot)Printed 'WHITE & bare from middle pickup'.To a pot casingwhite
8Middle bareVolume casing (upper Solder spot)To a pot casingbare
9Ground wire to bridgeVolume casing (upper Solder spot)To a pot casingblack
10Volume third lugVolume casing (lower Solder spot)Lug bent onto the casing.To a pot casingground
11Volume casing (lower Solder spot)Jack sleeveTo a pot casingblack
12Bridge blackRight wafer lug 3Wireblack
13Right wafer lug 3Right wafer lug 2Short jumper.Wireblack
14Neck blackRight wafer lug 5Wireblack
15Right wafer lug 5Right wafer lug 6Short jumper.Wireblack
16Middle redLeft wafer lug 3Runs over the top of the switch.Wirered
17Left wafer lug 3Left wafer lug 4Short jumper.Wireblack
18Left wafer lug 4Left wafer lug 5Short jumper.Wireblack
19Middle blackLeft wafer lug 8Printed 'middle green & black'.Wireblack
20Left wafer lug 8Left wafer lug 10Jumper.Wireblack
21Bridge whiteRight wafer lug 8Printed 'bridge red & white'.Wirewhite
22Bridge redRight wafer lug 8Printed 'bridge red & white'.Wirered
23Neck whiteRight wafer lug 10Printed 'neck red & white'.Wirewhite
24Neck redRight wafer lug 10Printed 'neck red & white'.Wirered
25Left wafer lug 1 (top)Right wafer lug 1 (top)Arcs over the top of the switch.Wireblack
26Right wafer lug 1 (top)Volume first lugRuns down past the pickup cables.Wireblack
27Left wafer lug 12 (bottom)Right wafer lug 12 (bottom)Loops under the switch.Wireblack
28Volume middle lugJack tipWireblack

What each position does

SettingThe sourceEngine result
Bridge full humbucker—Bridge stack (both coils).
Bridge & middle (both split, hum-canceling)—Middle stack (split to one coil) and Bridge stack (split to one coil) in parallel.
Middle full humbucker—Middle stack (both coils).
Middle & neck (both split, hum-canceling)—Neck stack (split to one coil) and Middle stack (split to one coil) in parallel.
Neck full humbucker—Neck stack (both coils).

Checked with the Tinkercaster wiring engine against the switching the source describes.

  • The sheet wires the middle pickup reversed (green and black are the series link on the switch, white is grounded); the editor checks recognise this reversed-lead wiring (hot and return leads joined as the link). The engine's per-position pickup selection and coil modes match all five legend positions.
  • Hum cancelling in the split positions depends on the real pickups' coil polarity, which this reference does not measure.
  • Pickup resistance is not specified, so no numeric meter readings are given.

Before you solder

Ticks are kept in this browser only, as a reminder. They are not a check of your joints. New to soldering? Read the soldering cheat sheet .

Check before plugging in

  • In positions 1, 3 and 5 the meter across the jack should read one whole pickup; in positions 2 and 4 two split pickups in parallel.
  • With the volume at zero, tip and sleeve should read as a short.

Measure across the output jack with a multimeter on its resistance range. No exact readings are given where the source does not specify the pickups.