Skip to content
Tinkercaster

Seymour Duncan wiring

Three singles five-way volume push-pull bridge-on two tones

Transcribed from the manufacturer wiring sheet and checked against the engine.

Viewed from the back of the controls, as you solder them.

Three singles five-way volume push-pull bridge-on two tonesThree singles five-way volume push-pull bridge-on two tones: Three singles five-way volume push-pull bridge-on two tones. Original Tinkercaster drawing with labelled terminals.Neck pickupMiddle pickupBridge pickup250k250k250k22nFwhiteblackwhiteblackwhiteblackT1T2T3T4T5T6T7T8lug1lug2lug3sw1sw2sw3sw4sw5sw6lug1lug2lug3lug1lug2lug3abtipsleevegroundNeck pickupMiddle pickupBridge pickup5-Way SwitchVolume 250k push/pull (bridge on)Neck tone 250kMiddle tone 250k.022 cap · 22nFOutput jackBridge ground

Open the interactive diagram to zoom, move components and try the switches.

Parts and values

Every pickup is the maker's own. “As specified” means the sheet names that part. “Example part” means the sheet names no model: the pickup shown is one of the maker's with the same leads, and any pot, cap or switch with the same value and lugs will do. “Generic” is a plain part such as a ground wire. “Not on the sheet; stand-in” means the sheet prints no value for that part, so the value shown is the usual one, not the maker's.

Understand this wiring

All Seymour Duncan wiring guides →

Connections

In soldering order: grounds first, then the switch, the pickups and the signal path.

#FromToHow
1Neck pickup gndVolume 250k push/pull (bridge on) casingWireblack
2Middle pickup gndVolume 250k push/pull (bridge on) casingWireblack
3Bridge pickup gndVolume 250k push/pull (bridge on) casingWireblack
4Volume 250k push/pull (bridge on) casingVolume 250k push/pull (bridge on) lug1Wireblack
5Volume 250k push/pull (bridge on) lug1Neck tone 250k casingWireblack
6Neck tone 250k casing.022 cap aWireyellow
7Neck tone 250k casingMiddle tone 250k casingWireblack
8Middle tone 250k casingOutput jack sleeveWireblack
9Bridge ground groundOutput jack sleeveWireblack
10Neck pickup hot5-Way Switch T2Wirewhite
11Middle pickup hot5-Way Switch T1Wirewhite
12Bridge pickup hot5-Way Switch T3Wirewhite
135-Way Switch T85-Way Switch T4Wireblack
145-Way Switch T4Volume 250k push/pull (bridge on) lug3Wiresignal
15Neck tone 250k lug25-Way Switch T6Wireblack
16Middle tone 250k lug25-Way Switch T5Wireblack
17Bridge pickup hotVolume 250k push/pull (bridge on) sw2Wirewhite
18Volume 250k push/pull (bridge on) lug2Output jack tipWiresignal
19.022 cap bNeck tone 250k lug1Wireyellow
20Neck tone 250k lug1Middle tone 250k lug1Wireblack
21Volume 250k push/pull (bridge on) sw1Volume 250k push/pull (bridge on) lug3Wireblack

What each position does

SettingThe sourceEngine result
Position 1; p5=downEngine reading of the transcribed board; matches the source legend.Bridge pickup.
Position 1; p5=upEngine reading of the transcribed board; matches the source legend.Bridge pickup.
Position 2; p5=downEngine reading of the transcribed board; matches the source legend.Middle pickup and Bridge pickup in parallel.
Position 2; p5=upEngine reading of the transcribed board; matches the source legend.Middle pickup and Bridge pickup in parallel.
Position 3; p5=downEngine reading of the transcribed board; matches the source legend.Middle pickup.
Position 3; p5=upEngine reading of the transcribed board; matches the source legend.Middle pickup and Bridge pickup in parallel.
Position 4; p5=downEngine reading of the transcribed board; matches the source legend.Neck pickup and Middle pickup in parallel.
Position 4; p5=upEngine reading of the transcribed board; matches the source legend.Neck pickup and Middle pickup and Bridge pickup in parallel.
Position 5; p5=downEngine reading of the transcribed board; matches the source legend.Neck pickup.
Position 5; p5=upEngine reading of the transcribed board; matches the source legend.Neck pickup and Bridge pickup in parallel.

Checked with the Tinkercaster wiring engine against the switching the source describes.

  • The sheet prints no pot taper; the pots are modelled as standard audio-taper 250k.

Before you solder

Ticks are kept in this browser only, as a reminder. They are not a check of your joints. New to soldering? Read the soldering cheat sheet .

Check before plugging in

    Measure across the output jack with a multimeter on its resistance range. No exact readings are given where the source does not specify the pickups.