Skip to content
Tinkercaster

Seymour Duncan wiring

Two humbuckers with a three-way toggle, a push/pull split volume and a push/pull phase tone

Two humbuckers · Three-way toggle · Push/pull volume (splits both) · Push/pull tone (phase)

Neck and bridge Seymour Duncan humbuckers on a three-way toggle with one 500k push/pull volume and one 500k push/pull tone with a .047 µF capacitor. The volume's push/pull splits both pickups by grounding each red–white link. The tone's push/pull reverses the neck pickup's black and green leads.

Viewed from the back of the controls, as you solder them.

Two humbuckers with a three-way toggle, a push/pull split volume and a push/pull phase toneTwo humbuckers with a three-way toggle, a push/pull split volume and a push/pull phase tone: Two humbuckers · Three-way toggle · Push/pull volume (splits both) · Push/pull tone (phase). Original Tinkercaster drawing with labelled terminals.Neck PickupBridge Pickup500k500k47nFblackgreenwhiteredbareblackgreenwhiteredbareT1T2T3T4lug1lug2lug3sw1sw2sw3sw4sw5sw6lug1lug2lug3sw1sw2sw3sw4sw5sw6abtipsleevegroundNeck PickupBridge Pickup3-Way ToggleVolume 500k push/pull splitTone 500k push/pull phase.047 cap · 47nFOutput JackBridge ground

Open the interactive diagram to zoom, move components and try the switches.

Parts and values

In the drawingValuePart
Neck PickupSource: Seymour Duncan Neck Pickup—Jazz Model SH-2 NeckExample partSame wiring for '59 Model SH-1 Neck, Duncan Distortion SH-6 Neck, Invader SH-8 Neck, Pearly Gates SH-PG1 Neck, Seymour Duncan SH-3 Stag Mag, Duncan Custom SH-5
Bridge PickupSource: Seymour Duncan Bridge Pickup—JB Model SH-4Example partSame wiring for '59 Model SH-1 Bridge, Duncan Custom SH-5, Duncan Distortion SH-6 Bridge, Invader SH-8 Bridge, Custom Five SH-14, Seymour Duncan SH-3 Stag Mag
3-Way ToggleSource: 3 Way Toggle—Switchcraft 3-Way ToggleExample part
Volume 500k push/pull splitSource: Volume 500k with Split Switch500k500k Push-Pull DPDTExample part
Tone 500k push/pull phaseSource: Tone 500k with Phase Switch500k500k Push-Pull DPDTExample part
.047 cap47nFOrange Drop .047µFExample part
Output Jack—Switchcraft #11Example part
Bridge groundSource: Bridge ground wire—Bridge ground wireGeneric

Every pickup is the maker's own. “As specified” means the sheet names that part. “Example part” means the sheet names no model: the pickup shown is one of the maker's with the same leads, and any pot, cap or switch with the same value and lugs will do. “Generic” is a plain part such as a ground wire. “Not on the sheet; stand-in” means the sheet prints no value for that part, so the value shown is the usual one, not the maker's.

Understand this wiring

All Seymour Duncan wiring guides →

Connections

In soldering order: grounds first, then the switch, the pickups and the signal path.

#FromToHow
1Bridge Pickup gndTone 500k push/pull phase sw5Wiregreen
2Neck bareTone casingShield or groundbare
3Tone push/pull bottom leftTone casingTo a pot casingblack
4Neck Pickup gndVolume 500k push/pull split casingWiregreen
5Bridge bareVolume casingShield or groundbare
6Toggle frameVolume casingTo a pot casingblack
7Volume push/pull bottom leftVolume casingTo a pot casingblack
8Volume right lugVolume casingLug bent onto the casing.To a pot casing
9.047 capTone casingTo a pot casingblack
10Volume casingTone casingTo a pot casingblack
11Bridge ground wireVolume casingWireblack
12Tone casingJack sleeveTo a pot casingblack
13Tone 500k push/pull phase sw33-Way Toggle T2Wireblack
14Neck Pickup hot3-Way Toggle T1Wireblack
15Toggle commonVolume left lug (input)Wireblack
16Neck whiteVolume push/pull middle rightWirewhite
17Neck redVolume push/pull middle rightShares the lug with the neck white.Wirered
18Bridge Pickup hotTone 500k push/pull phase sw2Wireblack
19Bridge whiteVolume push/pull middle leftWirewhite
20Bridge redVolume push/pull middle leftShares the lug with the bridge white.Wirered
21Tone push/pull top leftTone push/pull bottom rightOne leg of the X.Wireblack
22Tone push/pull top rightTone push/pull bottom leftThe other leg of the X.Wireblack
23Volume push/pull bottom leftVolume push/pull bottom rightWireblack
24Volume middle lugJack tipWireblack
25Volume left lugTone left lugWireblack
26Tone middle lug.047 capWireblack

What each position does

SettingThe sourceEngine result
Neck, both knobs down—Neck Pickup (both coils).
Both, both knobs down: in phase—Neck Pickup (both coils) and Bridge Pickup (both coils) in parallel.
Bridge, both knobs down—Bridge Pickup (both coils).
Neck, volume pulled (split), tone downPulling the volume splits both pickups.Neck Pickup (split to one coil).
Both, volume pulled (both split), tone downPulling the volume splits both pickups.Neck Pickup (split to one coil) and Bridge Pickup (split to one coil) in parallel.
Bridge, volume pulled (split), tone downPulling the volume splits both pickups.Bridge Pickup (split to one coil).
Neck, volume down, tone pulled (neck reversed)The neck does not pass through the phase switch.Neck Pickup (both coils).
Both, volume down, tone pulled: out of phaseBridge reversed against the neck.Neck Pickup (both coils) and Bridge Pickup (both coils) in parallel.
Bridge, volume down, tone pulledBridge alone sounds the same when reversed.Bridge Pickup (both coils).
Neck, volume and tone pulledNeck split; the phase switch does not affect the neck.Neck Pickup (split to one coil).
Both, volume and tone pulled: split and out of phaseBoth split; bridge reversed.Neck Pickup (split to one coil) and Bridge Pickup (split to one coil) in parallel.
Bridge, volume and tone pulledBridge split; alone it sounds the same when reversed.Bridge Pickup (split to one coil).

Checked with the Tinkercaster wiring engine against the switching the source describes.

  • Hum cancelling and phase follow the pickups' lead colours and coil polarity as Seymour Duncan publishes them; nothing here is measured.
  • Pickup resistance is not specified, so no numeric meter readings are given.

Before you solder

Ticks are kept in this browser only, as a reminder. They are not a check of your joints. New to soldering? Read the soldering cheat sheet .

Check before plugging in

  • In each toggle position the jack should read the selected pickup, or both in parallel in the middle.
  • Volume pulled: each red–white link should read continuity to ground.
  • Tone pulled in the middle position: the two pickups should be out of phase.

Measure across the output jack with a multimeter on its resistance range. No exact readings are given where the source does not specify the pickups.