Skip to content
Tinkercaster

Seymour Duncan wiring

Two Strat Stack Plus pickups and a single-coil-sized humbucker, super 5-way blade, volume

Two Strat Stack Plus · Single-coil-sized humbucker (bridge) · 4-pole super 5-way · One volume

Seymour Duncan sheet: Strat Stack Plus pickups in the neck and middle and a single-coil-sized humbucker in the bridge, on a 4-pole 5-way super switch with a 250k master volume and no tone control. The two in-between positions split both selected pickups; the other three use one pickup whole.

Viewed from the back of the controls, as you solder them.

Two Strat Stack Plus pickups and a single-coil-sized humbucker, super 5-way blade, volumeTwo Strat Stack Plus pickups and a single-coil-sized humbucker, super 5-way blade, volume: Two Strat Stack Plus · Single-coil-sized humbucker (bridge) · 4-pole super 5-way · One volume. Original Tinkercaster drawing with labelled terminals.Neck Strat Stack PlusMiddle Strat Stack PlusBridge single-coil-sized humbucker250kwhiteredblackbarewhiteredblackbareblackgreenwhiteredbareT1T2T3T4T5T6T7T8T9T10T11T12T13T14T15T16T17T18T19T20T21T22T23T24lug1lug2lug3tipsleeveNeck Strat Stack PlusMiddle Strat Stack PlusBridge single-coil-sized humbucker5-way super switchMaster volume 250kOutput jack

Open the interactive diagram to zoom, move components and try the switches.

Parts and values

In the drawingValuePart
Neck Strat Stack Plus—Strat Stack PlusExample part
Middle Strat Stack Plus—Strat Stack PlusExample part
Bridge single-coil-sized humbuckerSource: Bridge single coil sized humbucker—Little '59 SL59-1 Bridge (Strat-size)Example partSame wiring for JB Jr. SJBJ-1 Bridge (Strat-size), Hot Rails SHR-1 Bridge (Strat-size)
5-way super switch—Oak Grigsby 4-Pole 5-Way Super SwitchExample part
Master volume 250k250kCTS 250k Audio PotExample part
Output jack—Switchcraft #11Example part

Every pickup is the maker's own. “As specified” means the sheet names that part. “Example part” means the sheet names no model: the pickup shown is one of the maker's with the same leads, and any pot, cap or switch with the same value and lugs will do. “Generic” is a plain part such as a ground wire. “Not on the sheet; stand-in” means the sheet prints no value for that part, so the value shown is the usual one, not the maker's.

Understand this wiring

All Seymour Duncan wiring guides →

Connections

In soldering order: grounds first, then the switch, the pickups and the signal path.

#FromToHow
1Lower wafer lug 1Volume casing (lower Solder spot)Drawn broken where it passes behind the pickup cables.To a pot casingblack
2Lower wafer lug 12Volume casing (upper Solder spot)To a pot casingblack
3Neck blackVolume casing (upper Solder spot)To a pot casingblack
4Neck drainVolume casing (upper Solder spot)Drawn yellow.Shield or groundbare
5Middle blackVolume casing (upper Solder spot)To a pot casingblack
6Middle drainVolume casing (upper Solder spot)Drawn yellow.Shield or groundbare
7Bridge greenVolume casing (upper Solder spot)To a pot casinggreen
8Bridge bareVolume casing (upper Solder spot)Drawn lilac beside the green.Shield or groundbare
9Volume third lugVolume casingLug bent onto the casing.To a pot casing
10Volume casing (lower Solder spot)Jack sleeveWireblack
11Bridge blackUpper wafer lug 7Thin black lead leaving the bridge cable.Wireblack
12Upper wafer lug 7Upper wafer lug 8Short jumper.Wireblack
13Middle whiteUpper wafer lug 3Wirewhite
14Upper wafer lug 3Upper wafer lug 4Short jumper.Wireblack
15Upper wafer lug 4Upper wafer lug 5Short jumper.Wireblack
16Neck whiteUpper wafer lug 10Wirewhite
17Upper wafer lug 10Upper wafer lug 11Short jumper.Wireblack
18Upper wafer lug 1Upper wafer lug 12Arcs over the top and down the left side of the switch.Wireblack
19Upper wafer lug 12Volume first lugLoops under the switch.Wireblack
20Middle redLower wafer lug 3Wirered
21Lower wafer lug 3Lower wafer lug 5Jumper.Wireblack
22Bridge whiteLower wafer lug 8With the bridge red ('bridge red & white').Wirewhite
23Bridge redLower wafer lug 8With the bridge white ('bridge red & white').Wirered
24Neck redLower wafer lug 10Wirered
25Volume middle lugJack tipHops over the ground wires on the way down.Wireblack

What each position does

SettingThe sourceEngine result
Bridge pickup fullBridge pickup full.Bridge single-coil-sized humbucker (both coils).
Bridge-split + middle-splitBridge-split + middle-split (hum canceling).Middle Strat Stack Plus (split to one coil) and Bridge single-coil-sized humbucker (split to one coil) in parallel.
Middle pickup fullMiddle pickup full.Middle Strat Stack Plus (both coils).
Middle-split + neck-splitMiddle-split + neck-split (hum canceling).Neck Strat Stack Plus (split to one coil) and Middle Strat Stack Plus (split to one coil) in parallel.
Neck pickup fullNeck pickup full.Neck Strat Stack Plus (both coils).

Checked with the Tinkercaster wiring engine against the switching the source describes.

  • The on-board component drawn across the bottom-coil pads of each Strat Stack Plus (no value printed) is not modelled.
  • The engine cannot confirm the hum cancelling the legend prints for the two split pairs; it reports those positions as unknown.
  • The single-coil-sized bridge humbucker is drawn as the Little '59 SL59-1 (Strat-size); hum cancelling and phase follow its lead colours and coil polarity as Seymour Duncan publishes them.
  • Pickup resistance is not specified, so no numeric meter readings are given.

Before you solder

Ticks are kept in this browser only, as a reminder. They are not a check of your joints. New to soldering? Read the soldering cheat sheet .

Check before plugging in

  • In each switch position, the meter across the jack should read the pickup or split pair the legend names.
  • In position 1 the bridge red & white lug should read about one coil's resistance to ground (roughly half the pickup's total); in position 2 it should read zero, grounded.

Measure across the output jack with a multimeter on its resistance range. No exact readings are given where the source does not specify the pickups.