Skip to content
Tinkercaster

Seymour Duncan wiring

Tele two humbuckers, volume push/pull split, tone

Two Tele humbuckers · 3-way blade · Volume 500k push/pull split · Tone 500k

Seymour Duncan Tele sheet: neck and bridge humbuckers on a 3-way blade, a 500k push/pull volume, a 500k tone and a .047 cap. The neck humbucker is wired with its red as the output and its black and green joined on the push/pull; the bridge uses black as the output and its red and white on the other push/pull pole. Pulling the knob grounds both joints, so the drawing splits both humbuckers, although the title says the push/pull splits the neck pickup.

Viewed from the back of the controls, as you solder them.

Tele two humbuckers, volume push/pull split, toneTele two humbuckers, volume push/pull split, tone: Two Tele humbuckers · 3-way blade · Volume 500k push/pull split · Tone 500k. Original Tinkercaster drawing with labelled terminals.Neck PickupBridge Pickup500k500k47nFblackgreenwhiteredbareblackgreenwhiteredbareT1T2T3T4T5T6T7T8lug1lug2lug3sw1sw2sw3sw4sw5sw6lug1lug2lug3abtipsleevegroundNeck PickupBridge Pickup3-Way SwitchVolume 500k push/pullTone 500k.047 cap · 47nFOutput JackBridge ground wire

Open the interactive diagram to zoom, move components and try the switches.

Parts and values

In the drawingValuePart
Neck Pickup—Jazz Model SH-2 NeckExample partSame wiring for '59 Model SH-1 Neck, Seymour Duncan Antiquity Neck, Pearly Gates SH-PG1 Neck, Invader SH-8 Neck, Duncan Distortion SH-6 Neck, Alnico II Pro APH-1 Neck
Bridge Pickup—JB Model SH-4Example partSame wiring for Duncan Distortion SH-6 Bridge, Invader SH-8 Bridge, Duncan Custom SH-5, Seymour Duncan SH-3 Stag Mag, Seymour Duncan SH-11 Custom Custom, Seymour Duncan SH-2 Jazz Bridge
3-Way Switch—CRL 3-Way BladeExample part
Volume 500k push/pull500k500k Push-Pull DPDTExample part
Tone 500k500kCTS 500k Audio PotExample part
.047 cap47nFOrange Drop .047µFExample part
Output Jack—Switchcraft #11Example part
Bridge ground wire—Bridge ground wireGeneric

Every pickup is the maker's own. “As specified” means the sheet names that part. “Example part” means the sheet names no model: the pickup shown is one of the maker's with the same leads, and any pot, cap or switch with the same value and lugs will do. “Generic” is a plain part such as a ground wire. “Not on the sheet; stand-in” means the sheet prints no value for that part, so the value shown is the usual one, not the maker's.

Understand this wiring

All Seymour Duncan wiring guides →

Connections

In soldering order: grounds first, then the switch, the pickups and the signal path.

#FromToHow
1Neck greenPush/pull right middle lugWiregreen
2Neck whiteVolume casing (Solder spot)To a pot casingwhite
3Neck bareVolume casing (Solder spot)Shield or groundbare
4Bridge greenVolume casing (Solder spot)Labelled 'Green & bare'.To a pot casinggreen
5Bridge bareVolume casing (Solder spot)Shield or groundbare
6Bridge ground wireVolume casing (Solder spot)To a pot casingblack
7Push/pull left lug nearest the potVolume casing (Solder spot)To a pot casingblack
8Volume third lugVolume casingLug bent onto the casing.To a pot casing
9.047 capTone casing (Solder spot)To a pot casing
10Tone casing (Solder spot)Jack SleeveWireblack
11Volume casing (Solder spot)Tone casing (Solder spot)Drawn dashed.To a pot casingblack
12Neck redBlade top-right lugWirered
13Bridge blackBlade bottom-left lugLabelled 'Black'.Wireblack
14Blade top-left lugBlade second-left lugJumper.Wireblack
15Blade second-left lugBlade third-right lugDiagonal jumper.Wireblack
16Blade third-right lugBlade bottom-right lugJumper.Wireblack
17Blade bottom-right lugVolume first lugHops over the pickup leads.Wireblack
18Neck blackPush/pull right middle lugWireblack
19Bridge whitePush/pull left middle lugLabelled 'Red & White'; hops over the wire from the blade.Wirewhite
20Bridge redPush/pull left middle lugLabelled 'Red & White'.Wirered
21Push/pull left lug nearest the potPush/pull right lug nearest the potJumper.Wireblack
22Volume middle lugJack TipWireblack
23Volume first lugTone left lugWireblack
24Tone middle lug.047 capWireblack

What each position does

SettingThe sourceEngine result
Position 1 · push: humbuckers: neckNo position legend printed; positions follow the blade's standard contacts.Neck Pickup (both coils).
Position 2 · push: humbuckers: bothNo position legend printed; positions follow the blade's standard contacts.Neck Pickup (both coils) and Bridge Pickup (both coils) in parallel.
Position 3 · push: humbuckers: bridgeNo position legend printed; positions follow the blade's standard contacts.Bridge Pickup (both coils).
Position 1 · pull: split: neckDrawn: both coil joints are grounded when pulled. The title says the push/pull splits the neck pickup only; the drawing splits the neck pickup.Neck Pickup (split to one coil).
Position 2 · pull: split: bothDrawn: both coil joints are grounded when pulled. The title says the push/pull splits the neck pickup only; the drawing splits both pickups.Neck Pickup (split to one coil) and Bridge Pickup (split to one coil) in parallel.
Position 3 · pull: split: bridgeDrawn: both coil joints are grounded when pulled. The title says the push/pull splits the neck pickup only; the drawing splits the bridge pickup too.Bridge Pickup (split to one coil).

Not simulated: this circuit is drawn for reference only.

  • The title says the push/pull splits the neck pickup, but the drawing wires both humbuckers' coil joints to the push/pull commons; the expected states follow the drawing.
  • The dashed line between the Solder spots is not explained on the sheet; it is modelled as a ground wire.
  • The neck humbucker is wired reversed (red as the output, white to ground, black and green as the coil joint). The catalog's lead roles for this pickup differ from that; the editor checks recognise this reversed-lead wiring.
  • Which shaft position grounds the push/pull's commons follows the usual push/pull behaviour (pulled joins the middle lugs to the lugs nearest the pot).
  • Hum cancelling and phase follow the pickups' lead colours and coil polarity as Seymour Duncan publishes them; pickup resistance is not specified.

Before you solder

Ticks are kept in this browser only, as a reminder. They are not a check of your joints. New to soldering? Read the soldering cheat sheet .

Check before plugging in

  • Knob down: in each blade position the meter across the jack reads the full humbucker or pair selected.
  • Knob up: the neck black/green joint and the bridge red/white joint read ground.

Measure across the output jack with a multimeter on its resistance range. No exact readings are given where the source does not specify the pickups.