Skip to content
Tinkercaster

Seymour Duncan wiring

Two humbuckers with a three-way blade and a push/pull coil split

Two humbuckers · Three-way blade · Push/pull volume · No tone

Neck and bridge Seymour Duncan humbuckers on a three-way blade with one 500k push/pull volume and no tone. The push/pull splits both pickups at once by grounding each pickup's red–white link.

Viewed from the back of the controls, as you solder them.

Two humbuckers with a three-way blade and a push/pull coil splitTwo humbuckers with a three-way blade and a push/pull coil split: Two humbuckers · Three-way blade · Push/pull volume · No tone. Original Tinkercaster drawing with labelled terminals.Neck PickupBridge Pickup500kblackgreenwhiteredbareblackgreenwhiteredbareT1T2T3T4T5T6T7T8lug1lug2lug3sw1sw2sw3sw4sw5sw6tipsleevegroundNeck PickupBridge Pickup3-Way Blade SwitchVolume 500k push/pull splitOutput JackBridge ground

Open the interactive diagram to zoom, move components and try the switches.

Parts and values

In the drawingValuePart
Neck PickupSource: Seymour Duncan Neck Pickup—Jazz Model SH-2 NeckExample partSame wiring for '59 Model SH-1 Neck, Duncan Distortion SH-6 Neck, Invader SH-8 Neck, Pearly Gates SH-PG1 Neck, Seymour Duncan SH-3 Stag Mag, Duncan Custom SH-5
Bridge PickupSource: Seymour Duncan Bridge Pickup—JB Model SH-4Example partSame wiring for '59 Model SH-1 Bridge, Duncan Custom SH-5, Duncan Distortion SH-6 Bridge, Invader SH-8 Bridge, Custom Five SH-14, Seymour Duncan SH-3 Stag Mag
3-Way Blade SwitchSource: 3 Way Blade—CRL 3-Way BladeExample part
Volume 500k push/pull splitSource: Volume 500k with Split Switch500k500k Push-Pull DPDTExample part
Output Jack—Switchcraft #11Example part
Bridge groundSource: Bridge ground wire—Bridge ground wireGeneric

Every pickup is the maker's own. “As specified” means the sheet names that part. “Example part” means the sheet names no model: the pickup shown is one of the maker's with the same leads, and any pot, cap or switch with the same value and lugs will do. “Generic” is a plain part such as a ground wire. “Not on the sheet; stand-in” means the sheet prints no value for that part, so the value shown is the usual one, not the maker's.

Understand this wiring

All Seymour Duncan wiring guides →

Connections

In soldering order: grounds first, then the switch, the pickups and the signal path.

#FromToHow
1Neck greenVolume casingTo a pot casinggreen
2Neck bareVolume casingDrawn grey beside the green.Shield or groundbare
3Bridge greenVolume casingTo a pot casinggreen
4Bridge bareVolume casingDrawn grey beside the green.Shield or groundbare
5Push/pull bottom left lugVolume casingTo a pot casingblack
6Volume right lugVolume casingLug bent onto the lower solder spot.To a pot casing
7Volume casingJack sleeveWireblack
8Bridge ground wireVolume casingShield or groundblack
9Neck blackBlade top row, first lug (common)Wireblack
10Bridge blackBlade bottom row, fourth lug (common)Wireblack
11Blade bottom row, first lugBlade bottom row, second lugJumperblack
12Blade bottom row, second lugBlade top row, third lugJumperblack
13Blade top row, third lugBlade top row, fourth lugJumperblack
14Blade top row, fourth lugVolume left lug (input)Wireblack
15Neck whitePush/pull middle right lugWirewhite
16Neck redPush/pull middle right lugShares the lug with the neck white lead.Wirered
17Bridge whitePush/pull middle left lugWirewhite
18Bridge redPush/pull middle left lugShares the lug with the bridge white lead.Wirered
19Push/pull bottom left lugPush/pull bottom right lugJumperblack
20Volume middle lugJack tipWireblack

What each position does

SettingThe sourceEngine result
Neck, knob down: full humbucker—Neck Pickup (both coils).
Neck + bridge, knob down: both humbuckers—Neck Pickup (both coils) and Bridge Pickup (both coils) in parallel.
Bridge, knob down: full humbucker—Bridge Pickup (both coils).
Neck, knob pulled: single coilThe split switch splits both pickups.Neck Pickup (split to one coil).
Neck + bridge, knob pulled: both splitThe split switch splits both pickups.Neck Pickup (split to one coil) and Bridge Pickup (split to one coil) in parallel.
Bridge, knob pulled: single coilThe split switch splits both pickups.Bridge Pickup (split to one coil).

Checked with the Tinkercaster wiring engine against the switching the source describes.

  • Hum cancelling and phase follow the pickups' lead colours and coil polarity as Seymour Duncan publishes them; nothing here is measured.
  • Pickup resistance is not specified, so no numeric meter readings are given.
  • The source does not say which knob position splits; this follows the usual push/pull behaviour (pulled joins the middle lugs to the lugs nearest the pot).

Before you solder

Ticks are kept in this browser only, as a reminder. They are not a check of your joints. New to soldering? Read the soldering cheat sheet .

Check before plugging in

  • Knob down: in each blade position the meter across the jack reads the selected humbucker, or both in parallel in the middle.
  • Knob up: each reading drops to roughly one coil's resistance.
  • With the volume at zero, tip and sleeve should read as a short in every position.

Measure across the output jack with a multimeter on its resistance range. No exact readings are given where the source does not specify the pickups.