Skip to content
Tinkercaster
← All articles

Pickups & parts

DiMarzio Super Distortion wiring: colour code and the Les Paul sheet, lead by lead

How DiMarzio wires the Super Distortion DP100: red hot, green and bare to ground, black and white joined. Then its vintage Les Paul sheet, toggle to jack, and the one-humbucker version.

By Tinkercaster8 min read
A cream open-coil humbucker with red, white, green, black and bare leads, beside a three-way toggle switch, two pots and an amber capacitor.

The DiMarzio Super Distortion is a 4-conductor humbucker. For normal series humbucking, DiMarzio’s 4-conductor instructions say to solder the black and white leads together and tape the joint, use red as the hot output, and send green and bare to ground. The DiMarzio sheets in this article follow that code, including the vintage Les Paul sheet, which puts the Super Distortion in the bridge with two volumes, two tones and a Switchcraft straight toggle.

This article traces that Les Paul sheet as drawn in our library, from the leads to the jack, and then shows the simpler one-humbucker version.

The pickup

DiMarzio’s Super Distortion page lists it as a 4-conductor pickup with a ceramic magnet, introduced in 1974, available standard spaced or F-spaced. DiMarzio calls it “primarily a bridge position pickup, although it can be used in the neck position with a relatively low-gain amp”, and says it is designed for solid-body guitars. The same page recommends a 500K volume pot, a 500K tone pot and a .022 µF capacitor. The vintage Les Paul sheet and the 1 Humbucker 1 Volume 1 Tone sheet below use those values; the other two DiMarzio sheets mentioned here differ, as noted where they come up.

The four conductors are what make the extra modes possible. DiMarzio’s page says “4-conductor wiring allows instant access to Strat®-like split and series-parallel modes”. The sheets in this article do not use them: both keep black and white joined, so the pickup always runs as a series humbucker.

Lead Standard series wiring
Red Hot, to the volume input lug
Green Ground, to the back of the volume pot
Bare Ground, to the back of the volume pot
Black Soldered to white, taped, connected to nothing else
White Soldered to black, taped, connected to nothing else

DiMarzio’s instructions add one exception. If the pickup sounds out of phase when played with another pickup, use green as the hot and connect red and bare to ground.

The Les Paul diagram

Super Distortion vintage Les Paul wiring with straight toggleTwo humbuckers · Straight toggle · Two volumes · Two tonesNeck pickupBridge pickup500k500k500k500k22nF22nFredgreenblackwhitebarebaregreenredblackwhiteT1T2T3T4T5lug1lug2lug3lug1lug2lug3lug1lug2lug3lug1lug2lug3ababtipsleevegroundNeck pickupBridge pickupToggle (straight / straight short)Neck volume 500K custom taperNeck tone 500K custom taperBridge volume 500K custom taperBridge tone 500K custom taper.022µF (neck).022µF (bridge)Output jackBridge ground
DiMarzio wiring diagramSuper Distortion vintage Les Paul wiring with straight toggleTwo humbuckers · Straight toggle · Two volumes · Two tones

Super Distortion vintage Les Paul wiring with straight toggle, drawn by Tinkercaster from DiMarzio's Super Distortion Vintage Les Paul Wiring with Straight Toggle Switch sheet (PDF).

Parts, connections and bench checks ↗Open interactive diagram ↗

DiMarzio’s sheet names the bridge pickup, the Super Distortion DP100F, and says it “combines well” with three neck pickups: the PAF 36th Anniversary Neck (DP103), the PAF Pro (DP151) and the Air Norton (DP193). Our drawing uses the PAF Pro as its example neck pickup. Both neck and bridge pickups on the sheet carry the same five leads.

Part Compatible example
Bridge humbucker DiMarzio Super Distortion F-Spaced
Neck humbucker DiMarzio PAF Pro DP151
Toggle, Switchcraft straight (EP1101) or straight short (EP1102) Switchcraft 3-Way Toggle (two output tags)
Neck and bridge volumes, 500k custom taper CTS 500k Audio Pot
Neck and bridge tones, 500k custom taper CTS 500k Audio Pot
Two tone capacitors, .022 µF Orange Drop .022µF
Output jack, 2-conductor Switchcraft #11
Bridge ground Bridge ground wire

Lead by lead

The neck and bridge circuits are identical up to the toggle, so this table gives one side. Swap “neck” for “bridge” for the other. The drawing numbers pot lugs 1 to 3, with lug 1 the grounded end, lug 2 the wiper and lug 3 the input.

From To Lead
Pickup red Volume lug 3 (input) red
Pickup green Volume casing green
Pickup bare Volume casing bare
Pickup black Pickup white joined and taped
Volume lug 1 Volume casing ground
Volume lug 1 Tone casing ground
Volume lug 2 (wiper) .022µF capacitor signal
.022µF capacitor Tone lug 1 signal
Tone lug 2 (wiper) Tone casing ground
Volume lug 2 (wiper) Toggle, neck tag (bridge tag for the bridge side) signal

Then the shared wiring:

From To Lead
Neck tone casing Bridge tone casing ground
Toggle output tag Second toggle output tag jumper
Toggle output tag Output jack tip signal
Toggle frame tag Output jack sleeve ground
Bridge tone casing Output jack sleeve ground
Bridge ground Output jack sleeve ground

The drawing notes that DiMarzio’s sheet does not label the toggle tags, so they are mapped by function: one tag per pickup, two output tags joined by a jumper, and a frame tag to ground. That matches the two-output-tag Switchcraft in our catalog. Find the tags on your own switch with a meter before you solder; our humbucker to 3-way toggle article has a continuity table for it.

Why this counts as “vintage” wiring

The difference is where each capacitor starts. On this sheet the .022µF capacitor leaves the volume wiper (lug 2), the same lug that sends signal to the toggle, and lands on an outer lug of the tone pot. The tone wiper goes to the tone casing, which is ground.

DiMarzio publishes the other layout as a separate sheet, Super Distortion with straight or short toggle switch, which uses one volume and one tone for both pickups. Its volume is a 500K custom taper pot (EP1201), but its tone is a lower-value custom taper pot (EP1200), not the 500K tone the Super Distortion page recommends, with the same .022 µF capacitor. Read the tone value off DiMarzio’s PDF before you buy parts for it. That sheet is not drawn in our library yet, so follow DiMarzio’s PDF for it. The 3-way toggle article compares 50s and modern Les Paul wiring from other makers’ sheets.

What each toggle position does

Toggle Result in the diagram
Position 1 Neck pickup (both coils)
Position 2 Neck and bridge pickups (both coils) in parallel
Position 3 Bridge pickup (both coils)

In position 2 each pickup still passes through its own volume pot before the toggle joins them, so both volume pots stay in the circuit.

One humbucker instead of two

For a guitar with only a bridge humbucker, DiMarzio’s 1 Humbucker with 1 Volume and 1 Tone sheet uses the same lead colours. Our drawing of it uses the Super Distortion DP100 as its example pickup.

One humbucker with one volume and one toneOne humbucker · No switch · One volume · One toneBridge pickup500k500k22nFredgreenblackwhitebarelug1lug2lug3lug1lug2lug3tipsleeveabgroundBridge pickupVolume 500K custom taperTone 500K custom taperOutput jack.022µFBridge ground
DiMarzio wiring diagramOne humbucker with one volume and one toneOne humbucker · No switch · One volume · One tone

One humbucker with one volume and one tone, drawn by Tinkercaster from DiMarzio's 1 Humbucker with 1 Volume and 1 Tone sheet (PDF).

Parts, connections and bench checks ↗Open interactive diagram ↗

Red goes to the volume input lug, green and bare to the volume casing, and black and white are joined and insulated. The volume’s middle lug goes to the jack tip. Unlike the Les Paul sheet, the tone takes its signal from the volume input lug: the volume input lug runs to the tone wiper, and the .022µF capacitor sits between an outer tone lug and the tone casing. With no tone at all, DiMarzio’s 1 Humbucker 1 Volume sheet, drawn as one humbucker with one volume, keeps the same pickup connections and drops the tone pot.

Splitting or series-parallel

Neither sheet above switches anything inside the pickup. To use the split and parallel modes DiMarzio mentions, black and white come apart and go to a switch. DiMarzio Dual Sound wiring traces DiMarzio’s on-on-on toggle for series, split and parallel on the same colour code, and coil split wiring diagram explains what a split does to the hum.

Before you solder

  • Check the leads against the colour code before you cut anything. Black and white are the pair to join, red is hot.
  • Insulate the black and white joint. It must touch nothing else.
  • On the Les Paul sheet, check that each volume wiper carries two wires: one to the capacitor and one to the toggle.
  • Set a meter to continuity and confirm each toggle position against the table above before you close the guitar. The multimeter course covers the setup.

Next step

Open the Super Distortion Les Paul diagram and keep it beside the bench while you wire. Other DiMarzio layouts are in the DiMarzio section of the library.

References

From the Tinkercaster library

Manufacturer sources

Keep reading

Pickups & parts15 min read

250k vs 500k pots: which do you need?

Pot value is a load on your pickup's resonant peak. What 330 library diagrams specify for single coils, humbuckers, P90s and actives, how to read a CTS part number, and when to break the rule.

Read article
Pickups & parts13 min read

Gibson vs Fender pickup wire colour codes

Gibson and Fender codes from their own wiring sheets, the Seymour Duncan, DiMarzio, Tonerider and Fralin 4-conductor codes, where the charts disagree, and how to identify unknown leads with a meter.

Read article