Parts and values
| In the drawing | Value | Part |
|---|---|---|
| Neck pickup | — | Jazz Model SH-2 Neck |
| Bridge pickup | — | JB Model SH-4 |
| 3-Way Blade Switch | — | CRL 3-Way Blade |
| Volume 250k push/pull (neck split) | 250k | 250k Push-Pull DPDT |
| Tone 250k push/pull (bridge split) | 250k | 250k Push-Pull DPDT |
| .047 cap | 47nF | Orange Drop .047µF |
| Output Jack | — | Switchcraft #11 |
| Bridge Ground Wire | — | Bridge ground wire |
Every pickup is the maker's own. “As specified” means the sheet names that part. “Example part” means the sheet names no model: the pickup shown is one of the maker's with the same leads, and any pot, cap or switch with the same value and lugs will do. “Generic” is a plain part such as a ground wire. “Not on the sheet; stand-in” means the sheet prints no value for that part, so the value shown is the usual one, not the maker's.
Understand this wiring
- Seymour Duncan humbucker wire colors
See the pickup, recognise its two halves, and learn where each coloured wire goes.
- Reading Seymour Duncan push/pull switch diagrams
Turning the knob and pulling it do different jobs. See the actual part, then try its switch connections.
Connections
In soldering order: grounds first, then the switch, the pickups and the signal path.
| # | From | To | How |
|---|---|---|---|
| 1 | Neck pickup gnd | Volume 250k push/pull (neck split) casing | Wire |
| 2 | Neck pickup bare | Volume 250k push/pull (neck split) casing | Wire |
| 3 | Bridge pickup gnd | Volume 250k push/pull (neck split) casing | Wire |
| 4 | Bridge pickup bare | Volume 250k push/pull (neck split) casing | Wire |
| 5 | Volume 250k push/pull (neck split) lug1 | Volume 250k push/pull (neck split) casing | Wire |
| 6 | .047 cap b | Tone 250k push/pull (bridge split) casing | Wire |
| 7 | Volume 250k push/pull (neck split) casing | Tone 250k push/pull (bridge split) casing | Wire |
| 8 | Tone 250k push/pull (bridge split) casing | Output Jack sleeve | Wire |
| 9 | Tone 250k push/pull (bridge split) sw1 | Tone 250k push/pull (bridge split) casing | Wire |
| 10 | Bridge Ground Wire ground | Volume 250k push/pull (neck split) casing | Wire |
| 11 | Volume 250k push/pull (neck split) sw1 | Volume 250k push/pull (neck split) casing | Wire |
| 12 | Neck pickup hot | 3-Way Blade Switch T8 | Wire |
| 13 | Bridge pickup hot | 3-Way Blade Switch T4 | Wire |
| 14 | 3-Way Blade Switch T3 | 3-Way Blade Switch T2 | Wire |
| 15 | 3-Way Blade Switch T2 | 3-Way Blade Switch T6 | Wire |
| 16 | 3-Way Blade Switch T6 | 3-Way Blade Switch T5 | Wire |
| 17 | 3-Way Blade Switch T5 | Volume 250k push/pull (neck split) lug3 | Wire |
| 18 | Neck pickup white | Volume 250k push/pull (neck split) sw2 | Wire |
| 19 | Neck pickup red | Volume 250k push/pull (neck split) sw2 | Wire |
| 20 | Bridge pickup white | Tone 250k push/pull (bridge split) sw2 | Wire |
| 21 | Bridge pickup red | Tone 250k push/pull (bridge split) sw2 | Wire |
| 22 | Volume 250k push/pull (neck split) lug2 | Output Jack tip | Wire |
| 23 | Volume 250k push/pull (neck split) lug3 | Tone 250k push/pull (bridge split) lug1 | Wire |
| 24 | Tone 250k push/pull (bridge split) lug2 | .047 cap a | Wire |
What each position does
| Setting | The source | Engine result |
|---|---|---|
| Position 1; p4=down, p5=down | Engine reading of the transcribed board; matches the source legend. | Neck pickup (both coils). |
| Position 1; p4=down, p5=up | Engine reading of the transcribed board; matches the source legend. | Neck pickup (both coils). |
| Position 1; p4=up, p5=down | Engine reading of the transcribed board; matches the source legend. | Neck pickup (split to one coil). |
| Position 1; p4=up, p5=up | Engine reading of the transcribed board; matches the source legend. | Neck pickup (split to one coil). |
| Position 2; p4=down, p5=down | Engine reading of the transcribed board; matches the source legend. | Neck pickup (both coils) and Bridge pickup (both coils) in parallel. |
| Position 2; p4=down, p5=up | Engine reading of the transcribed board; matches the source legend. | Neck pickup (both coils) and Bridge pickup (split to one coil) in parallel. |
| Position 2; p4=up, p5=down | Engine reading of the transcribed board; matches the source legend. | Neck pickup (split to one coil) and Bridge pickup (both coils) in parallel. |
| Position 2; p4=up, p5=up | Engine reading of the transcribed board; matches the source legend. | Neck pickup (split to one coil) and Bridge pickup (split to one coil) in parallel. |
| Position 3; p4=down, p5=down | Engine reading of the transcribed board; matches the source legend. | Bridge pickup (both coils). |
| Position 3; p4=down, p5=up | Engine reading of the transcribed board; matches the source legend. | Bridge pickup (split to one coil). |
| Position 3; p4=up, p5=down | Engine reading of the transcribed board; matches the source legend. | Bridge pickup (both coils). |
| Position 3; p4=up, p5=up | Engine reading of the transcribed board; matches the source legend. | Bridge pickup (split to one coil). |
Checked with the Tinkercaster wiring engine against the switching the source describes.
- Custom-taper pots are treated as linear by the simulator.
Before you solder
Ticks are kept in this browser only, as a reminder. They are not a check of your joints. New to soldering? Read the soldering cheat sheet .
Check before plugging in
Measure across the output jack with a multimeter on its resistance range. No exact readings are given where the source does not specify the pickups.