Parts and values
| In the drawing | Value | Part |
|---|---|---|
| Neck Pickup | — | Jazz Model SH-2 Neck |
| Bridge Pickup | — | JB Model SH-4 |
| 3-Way Blade Switch | — | CRL 3-Way Blade |
| Volume 250k push/pull split | 250k | 250k Push-Pull DPDT |
| Tone 250k push/pull phase | 250k | 250k Push-Pull DPDT |
| .047 cap | 47nF | Orange Drop .047µF |
| Output Jack | — | Switchcraft #11 |
| Bridge ground | — | Bridge ground wire |
Every pickup is the maker's own. “As specified” means the sheet names that part. “Example part” means the sheet names no model: the pickup shown is one of the maker's with the same leads, and any pot, cap or switch with the same value and lugs will do. “Generic” is a plain part such as a ground wire. “Not on the sheet; stand-in” means the sheet prints no value for that part, so the value shown is the usual one, not the maker's.
Understand this wiring
- Seymour Duncan humbucker wire colors
See the pickup, recognise its two halves, and learn where each coloured wire goes.
- Reading Seymour Duncan push/pull switch diagrams
Turning the knob and pulling it do different jobs. See the actual part, then try its switch connections.
Connections
In soldering order: grounds first, then the switch, the pickups and the signal path.
| # | From | To | How |
|---|---|---|---|
| 1 | Neck Pickup white | Volume 250k push/pull split casing | Wire |
| 2 | Neck Pickup gnd | Volume 250k push/pull split sw5 | Wire |
| 3 | Neck Pickup bare | Volume 250k push/pull split casing | Wire |
| 4 | Tone 250k push/pull phase sw1 | Tone 250k push/pull phase casing | Wire |
| 5 | Bridge Pickup bare | Volume 250k push/pull split casing | Wire |
| 6 | Volume 250k push/pull split sw1 | Volume 250k push/pull split casing | Wire |
| 7 | Volume 250k push/pull split lug1 | Volume 250k push/pull split casing | Wire |
| 8 | .047 cap b | Tone 250k push/pull phase casing | Wire |
| 9 | Volume 250k push/pull split casing | Tone 250k push/pull phase casing | Wire |
| 10 | Bridge ground ground | Tone 250k push/pull phase casing | Wire |
| 11 | Tone 250k push/pull phase casing | Output Jack sleeve | Wire |
| 12 | Bridge Pickup gnd | Tone 250k push/pull phase sw2 | Wire |
| 13 | Neck Pickup red | 3-Way Blade Switch T8 | Wire |
| 14 | Tone 250k push/pull phase sw3 | 3-Way Blade Switch T4 | Wire |
| 15 | 3-Way Blade Switch T3 | 3-Way Blade Switch T2 | Wire |
| 16 | 3-Way Blade Switch T2 | 3-Way Blade Switch T6 | Wire |
| 17 | 3-Way Blade Switch T6 | 3-Way Blade Switch T5 | Wire |
| 18 | 3-Way Blade Switch T5 | Volume 250k push/pull split lug3 | Wire |
| 19 | Neck Pickup hot | Volume 250k push/pull split sw5 | Wire |
| 20 | Bridge Pickup white | Volume 250k push/pull split sw2 | Wire |
| 21 | Bridge Pickup red | Volume 250k push/pull split sw2 | Wire |
| 22 | Bridge Pickup hot | Tone 250k push/pull phase sw5 | Wire |
| 23 | Tone 250k push/pull phase sw3 | Tone 250k push/pull phase sw4 | Wire |
| 24 | Tone 250k push/pull phase sw6 | Tone 250k push/pull phase sw1 | Wire |
| 25 | Volume 250k push/pull split sw1 | Volume 250k push/pull split sw4 | Wire |
| 26 | Volume 250k push/pull split lug2 | Output Jack tip | Wire |
| 27 | Volume 250k push/pull split lug3 | Tone 250k push/pull phase lug1 | Wire |
| 28 | Tone 250k push/pull phase lug2 | .047 cap a | Wire |
What each position does
| Setting | The source | Engine result |
|---|---|---|
| Position 1; p4=down, p5=down | Engine reading of the transcribed board; matches the source legend. | Neck Pickup (both coils). |
| Position 1; p4=down, p5=up | Engine reading of the transcribed board; matches the source legend. | Neck Pickup (both coils). |
| Position 1; p4=up, p5=down | Engine reading of the transcribed board; matches the source legend. | Neck Pickup (split to one coil). |
| Position 1; p4=up, p5=up | Engine reading of the transcribed board; matches the source legend. | Neck Pickup (split to one coil). |
| Position 2; p4=down, p5=down | Engine reading of the transcribed board; matches the source legend. | Neck Pickup (both coils) and Bridge Pickup (both coils) in parallel. |
| Position 2; p4=down, p5=up | Engine reading of the transcribed board; matches the source legend. | Neck Pickup (both coils) and Bridge Pickup (both coils) in parallel. |
| Position 2; p4=up, p5=down | Engine reading of the transcribed board; matches the source legend. | Neck Pickup (split to one coil) and Bridge Pickup (split to one coil) in parallel. |
| Position 2; p4=up, p5=up | Engine reading of the transcribed board; matches the source legend. | Neck Pickup (split to one coil) and Bridge Pickup (split to one coil) in parallel. |
| Position 3; p4=down, p5=down | Engine reading of the transcribed board; matches the source legend. | Bridge Pickup (both coils). |
| Position 3; p4=down, p5=up | Engine reading of the transcribed board; matches the source legend. | Bridge Pickup (both coils). |
| Position 3; p4=up, p5=down | Engine reading of the transcribed board; matches the source legend. | Bridge Pickup (split to one coil). |
| Position 3; p4=up, p5=up | Engine reading of the transcribed board; matches the source legend. | Bridge Pickup (split to one coil). |
Checked with the Tinkercaster wiring engine against the switching the source describes.
- Custom-taper pots are treated as linear by the simulator.
Before you solder
Ticks are kept in this browser only, as a reminder. They are not a check of your joints. New to soldering? Read the soldering cheat sheet .
Check before plugging in
Measure across the output jack with a multimeter on its resistance range. No exact readings are given where the source does not specify the pickups.