Skip to content
Tinkercaster

Seymour Duncan wiring

Tele two Tele stacks, volume push-pull split, tone

Two Tele stacks · Three-way · Volume push/pull split · Tone

Transcribed from the manufacturer wiring sheet and checked against the engine.

Viewed from the back of the controls, as you solder them.

Tele two Tele stacks, volume push-pull split, toneTele two Tele stacks, volume push-pull split, tone: Two Tele stacks · Three-way · Volume push/pull split · Tone. Original Tinkercaster drawing with labelled terminals.Neck Tele stackBridge Tele stack250k250k47nFblackwhiteredgreenbareblackwhiteredgreenbareT1T2T3T4T5T6T7T8lug1lug2lug3sw1sw2sw3sw4sw5sw6lug1lug2lug3abtipsleevegroundNeck Tele stackBridge Tele stack3-Way BladeVolume 250k push/pullTone 250k.047 cap · 47nFOutput JackGround wire from bridge

Open the interactive diagram to zoom, move components and try the switches.

Parts and values

In the drawingValuePart
Neck Tele stack—Seymour Duncan Vintage Stack for Tele NeckExample part
Bridge Tele stack—Seymour Duncan Vintage Stack for Tele BridgeExample part
3-Way Blade—CRL 3-Way BladeExample part
Volume 250k push/pull250k250k Push-Pull DPDTExample part
Tone 250k250kCTS 250k Audio PotExample part
.047 cap47nFOrange Drop .047µFExample part
Output Jack—Switchcraft #11Example part
Ground wire from bridge—Bridge ground wireGeneric

Every pickup is the maker's own. “As specified” means the sheet names that part. “Example part” means the sheet names no model: the pickup shown is one of the maker's with the same leads, and any pot, cap or switch with the same value and lugs will do. “Generic” is a plain part such as a ground wire. “Not on the sheet; stand-in” means the sheet prints no value for that part, so the value shown is the usual one, not the maker's.

Understand this wiring

All Seymour Duncan wiring guides →

Connections

In soldering order: grounds first, then the switch, the pickups and the signal path.

#FromToHow
1w7 as drawnw7 as drawnWiregreen
2w8 as drawnw8 as drawnWirebare
3w9 as drawnw9 as drawnWiregreen
4w10 as drawnw10 as drawnWirebare
5w11 as drawnw11 as drawnWireblack
6w12 as drawnw12 as drawnWireground
7w16 as drawnw16 as drawnWireblack
8w17 as drawnw17 as drawnWireblack
9w18 as drawnw18 as drawnWireblack
10w23 as drawnw23 as drawnWireblack
11w24 as drawnw24 as drawnWireblack
12w1 as drawnw1 as drawnWireblack
13w2 as drawnw2 as drawnWireblack
14w3 as drawnw3 as drawnWireblack
15w4 as drawnw4 as drawnWireblack
16w5 as drawnw5 as drawnWireblack
17w6 as drawnw6 as drawnWireblack
18w19 as drawnw19 as drawnWirewhite
19w20 as drawnw20 as drawnWirered
20w21 as drawnw21 as drawnWirewhite
21w22 as drawnw22 as drawnWirered
22w13 as drawnw13 as drawnWireblack
23w14 as drawnw14 as drawnWireblack
24w15 as drawnw15 as drawnWireblack

What each position does

SettingThe sourceEngine result
Position 1Engine reading of the transcribed board.Neck Tele stack (both coils).
Position 1 (pull)Engine reading of the transcribed board.Neck Tele stack (split to one coil).
Position 2Engine reading of the transcribed board.Neck Tele stack (both coils) and Bridge Tele stack (both coils) in parallel.
Position 2 (pull)Engine reading of the transcribed board.Neck Tele stack (split to one coil) and Bridge Tele stack (split to one coil) in parallel.
Position 3Engine reading of the transcribed board.Bridge Tele stack (both coils).
Position 3 (pull)Engine reading of the transcribed board.Bridge Tele stack (split to one coil).

Checked with the Tinkercaster wiring engine against the switching the source describes.

  • Tele stack pickups are drawn as their Vintage Stack for Tele catalog parts; stacked construction is not modelled beyond series coils.

Before you solder

Ticks are kept in this browser only, as a reminder. They are not a check of your joints. New to soldering? Read the soldering cheat sheet .

Check before plugging in

    Measure across the output jack with a multimeter on its resistance range. No exact readings are given where the source does not specify the pickups.