Skip to content
Tinkercaster

Seymour Duncan wiring

Telecaster with a neck humbucker, a Tele humbucker and two push/pull split volumes

Neck humbucker · Bridge Tele humbucker · Three-way blade · Two push/pull volumes

A Telecaster with a full-size humbucker at the neck and a Tele-size humbucker at the bridge, each on its own 250k push/pull volume ahead of the three-way blade. Pulling a volume splits its pickup; there is no tone control.

Viewed from the back of the controls, as you solder them.

Telecaster with a neck humbucker, a Tele humbucker and two push/pull split volumesTelecaster with a neck humbucker, a Tele humbucker and two push/pull split volumes: Neck humbucker · Bridge Tele humbucker · Three-way blade · Two push/pull volumes. Original Tinkercaster drawing with labelled terminals.Neck humbuckerBridge Tele humbucker250k250kblackgreenwhiteredbareblackwhiteredgreenbareT1T2T3T4T5T6T7T8lug1lug2lug3sw1sw2sw3sw4sw5sw6lug1lug2lug3sw1sw2sw3sw4sw5sw6tipsleevegroundNeck humbuckerBridge Tele humbucker3-Way SwitchNeck Volume 250k push/pullBridge Volume 250k push/pullOutput JackBridge ground wire

Open the interactive diagram to zoom, move components and try the switches.

Parts and values

In the drawingValuePart
Neck humbucker—Jazz Model SH-2 NeckExample partSame wiring for '59 Model SH-1 Neck, Seymour Duncan Antiquity Neck, Pearly Gates SH-PG1 Neck, Invader SH-8 Neck, Duncan Distortion SH-6 Neck, Alnico II Pro APH-1 Neck
Bridge Tele humbucker—Seymour Duncan Hot Rails for TeleExample part
3-Way Switch—CRL 3-Way BladeExample part
Neck Volume 250k push/pull250k250k Push-Pull DPDTExample part
Bridge Volume 250k push/pull250k250k Push-Pull DPDTExample part
Output Jack—Switchcraft #11Example part
Bridge ground wire—Bridge ground wireExample part

Every pickup is the maker's own. “As specified” means the sheet names that part. “Example part” means the sheet names no model: the pickup shown is one of the maker's with the same leads, and any pot, cap or switch with the same value and lugs will do. “Generic” is a plain part such as a ground wire. “Not on the sheet; stand-in” means the sheet prints no value for that part, so the value shown is the usual one, not the maker's.

Understand this wiring

All Seymour Duncan wiring guides →

Connections

In soldering order: grounds first, then the switch, the pickups and the signal path.

#FromToHow
1Neck Volume 250k push/pull sw1Neck Volume 250k push/pull casingWireblack
2Neck humbucker gndNeck Volume 250k push/pull casingWiregreen
3Neck humbucker bareNeck Volume 250k push/pull casingWirebare
4Bridge Volume 250k push/pull sw1Bridge Volume 250k push/pull casingWireblack
5Bridge Tele humbucker gndBridge Volume 250k push/pull casingWiregreen
6Bridge Tele humbucker bareBridge Volume 250k push/pull casingWirebare
7Bridge ground wire groundNeck Volume 250k push/pull casingWireblack
8Neck Volume 250k push/pull lug1Neck Volume 250k push/pull casingWireground
9Bridge Volume 250k push/pull lug1Bridge Volume 250k push/pull casingWireground
10Neck Volume 250k push/pull casingBridge Volume 250k push/pull casingWireblack
11Bridge Volume 250k push/pull casingOutput Jack sleeveWireblack
12Neck Volume 250k push/pull lug23-Way Switch T8Wireblack
13Bridge Volume 250k push/pull lug23-Way Switch T4Wireblack
143-Way Switch T33-Way Switch T2Wireblack
153-Way Switch T23-Way Switch T6Wireblack
163-Way Switch T63-Way Switch T5Wireblack
173-Way Switch T5Output Jack tipWireblack
18Neck humbucker redNeck Volume 250k push/pull sw2Wirered
19Neck humbucker whiteNeck Volume 250k push/pull sw2Wirewhite
20Neck humbucker hotNeck Volume 250k push/pull lug3Wireblack
21Bridge Tele humbucker redBridge Volume 250k push/pull sw2Wirered
22Bridge Tele humbucker whiteBridge Volume 250k push/pull sw2Wirewhite
23Bridge Tele humbucker hotBridge Volume 250k push/pull lug3Wireblack

What each position does

SettingThe sourceEngine result
Position 1 p4=down p5=downEngine reading of the transcribed board.Neck humbucker (both coils).
Position 1 p4=down p5=upEngine reading of the transcribed board.Neck humbucker (both coils).
Position 1 p4=up p5=downEngine reading of the transcribed board.Neck humbucker (split to one coil).
Position 1 p4=up p5=upEngine reading of the transcribed board.Neck humbucker (split to one coil).
Position 2 p4=down p5=downEngine reading of the transcribed board.Neck humbucker (both coils) and Bridge Tele humbucker (both coils) in parallel.
Position 2 p4=down p5=upEngine reading of the transcribed board.Neck humbucker (both coils) and Bridge Tele humbucker (split to one coil) in parallel.
Position 2 p4=up p5=downEngine reading of the transcribed board.Neck humbucker (split to one coil) and Bridge Tele humbucker (both coils) in parallel.
Position 2 p4=up p5=upEngine reading of the transcribed board.Neck humbucker (split to one coil) and Bridge Tele humbucker (split to one coil) in parallel.
Position 3 p4=down p5=downEngine reading of the transcribed board.Bridge Tele humbucker (both coils).
Position 3 p4=down p5=upEngine reading of the transcribed board.Bridge Tele humbucker (split to one coil).
Position 3 p4=up p5=downEngine reading of the transcribed board.Bridge Tele humbucker (both coils).
Position 3 p4=up p5=upEngine reading of the transcribed board.Bridge Tele humbucker (split to one coil).

Checked with the Tinkercaster wiring engine against the switching the source describes.

  • Custom tapers are not reproduced; pots are simulated as linear.
  • Pickup resistance is not specified, so no numeric meter readings are given.

Before you solder

Ticks are kept in this browser only, as a reminder. They are not a check of your joints. New to soldering? Read the soldering cheat sheet .

Check before plugging in

    Measure across the output jack with a multimeter on its resistance range. No exact readings are given where the source does not specify the pickups.