Skip to content
Tinkercaster

Seymour Duncan wiring

Tele two Tele stacks, volume push-pull power boost, tone

Two Tele stacks · Blade · Volume push/pull · Tone

Two Tele stacks on a 3-way blade with a push/pull volume and a tone. Pulling the volume reverses one coil of the bridge stack: more output, but the stack no longer cancels hum.

Viewed from the back of the controls, as you solder them.

Tele two Tele stacks, volume push-pull power boost, toneTele two Tele stacks, volume push-pull power boost, tone: Two Tele stacks · Blade · Volume push/pull · Tone. Original Tinkercaster drawing with labelled terminals.Neck Tele stackBridge Tele stack250k250k47nFblackwhiteredgreenbareblackwhiteredgreenbareT1T2T3T4T5T6T7T8lug1lug2lug3sw1sw2sw3sw4sw5sw6lug1lug2lug3abtipsleevegroundNeck Tele stackBridge Tele stack3-Way BladeVolume push/pull · 250kTone · 250k.047 cap · 47nFOutput JackGround wire from bridge

Open the interactive diagram to zoom, move components and try the switches.

Parts and values

In the drawingValuePart
Neck Tele stack—Seymour Duncan Vintage Stack for Tele NeckExample part
Bridge Tele stack—Seymour Duncan Vintage Stack for Tele BridgeExample part
3-Way Blade—CRL 3-Way BladeExample part
Volume push/pull250kNot on the sheet; stand-in250k Push-Pull DPDTExample part
Tone250kNot on the sheet; stand-inCTS 250k Audio PotExample part
.047 cap47nFOrange Drop .047µFExample part
Output Jack—Switchcraft #11Example part
Ground wire from bridge—Bridge ground wireGeneric

Every pickup is the maker's own. “As specified” means the sheet names that part. “Example part” means the sheet names no model: the pickup shown is one of the maker's with the same leads, and any pot, cap or switch with the same value and lugs will do. “Generic” is a plain part such as a ground wire. “Not on the sheet; stand-in” means the sheet prints no value for that part, so the value shown is the usual one, not the maker's.

Understand this wiring

All Seymour Duncan wiring guides →

Connections

In soldering order: grounds first, then the switch, the pickups and the signal path.

#FromToHow
1Neck stack greenVolume casingWiregreen
2Neck stack bareVolume casingWirebare
3Bridge stack greenVolume casingWiregreen
4Bridge stack bareVolume casingWirebare
5Ground wire from bridgeVolume casingWireblack
6Volume push/pull lug1Volume casingWireground
7.047 capTone casingWireblack
8Tone casingOutput Jack sleeveWireblack
9Volume casingTone casingWireblack
10Neck stack black3-Way Blade neck lugWireblack
11Volume push/pull pole B down3-Way Blade bridge lugThe bridge stack reaches the blade from the push/pull's lower right lug.Wireblack
123-Way Blade T33-Way Blade T2Wireblack
133-Way Blade T23-Way Blade T6Wireblack
143-Way Blade T63-Way Blade T5Wireblack
153-Way Blade T3Volume push/pull lug3Wireblack
16Neck stack whiteNeck stack redSoldered together and taped off.Joined and insulatedred
17Bridge stack blackVolume push/pull pole B commonWireblack
18Bridge stack whiteVolume push/pull pole A commonWirewhite
19Bridge stack redVolume push/pull pole A downWirered
20Volume push/pull lug2Output Jack tipWireblack
21Volume push/pull lug3Tone lug1Wireblack
22Tone lug2.047 capWireblack
23Volume push/pull pole A upVolume push/pull pole B downOne leg of the cross: pulled, white reaches the output.Wirewhite
24Volume push/pull pole A downVolume push/pull pole B upOther leg of the cross: pulled, black meets red, so the first coil runs reversed.Wireblack

What each position does

SettingThe sourceEngine result
NeckEngine reading of the transcribed board.Neck Tele stack (both coils).
Neck (volume pulled)The push/pull does not touch the neck stack.Neck Tele stack (both coils).
Neck + bridgeEngine reading of the transcribed board.Neck Tele stack (both coils) and Bridge Tele stack (both coils) in parallel.
Neck + bridge (bridge boosted)Sheet: in UP position output is boosted; the bridge stack's coils stay in series, one reversed.Neck Tele stack (both coils) and Bridge Tele stack (both coils) in parallel.
BridgeEngine reading of the transcribed board.Bridge Tele stack (both coils).
Bridge, boostedSheet: in UP position output is boosted, but hum-canceling is lost; both coils in series, one reversed.Bridge Tele stack (both coils).

Checked with the Tinkercaster wiring engine against the switching the source describes.

  • Tele stack pickups are drawn as their Vintage Stack for Tele catalog parts; stacked construction is not modelled beyond series coils.

Before you solder

Ticks are kept in this browser only, as a reminder. They are not a check of your joints. New to soldering? Read the soldering cheat sheet .

Check before plugging in

    Measure across the output jack with a multimeter on its resistance range. No exact readings are given where the source does not specify the pickups.